Abstract:Magnesium alloy AZ91D is used extensively in the automotive industry because of its high strength-to-weight ratio. Typically, components produced using the alloy are required to have good surface finish and to contribute to high productivity but require long cutting times. Cryogenic cooling is an environmentally friendly technology which has been proven to improve cutting tool life and surface finish. This paper presents an investigation on the effects of dry and cryogenic cutting conditions at a high cutting speed regime for milling of magnesium alloy. This study focused on a high-speed regime due to the chips of magnesium alloy being highly combustible and an effective means of decreasing the temperature in the cutting zone was of great concern. The machining experiment was carried out using uncoated carbide end milling utilizing a full factorial design (L16) with cutting speeds of 900 m/min and 1300 m/min, feed rate of 0.02 mm/tooth and 0.05 mm/tooth, axial depth of cut at 0.2 mm and 0.3 mm, and radial depth of cut at 10 mm and 40 mm. For dry machining, the longest tool life at flank wear (VBmax) of 0.21 mm was at 30 min, which was obtained at cutting speeds of 1300 m/min, feed rate of 0.02 mm/tooth, axial depth of cut at 0.2 mm, and radial depth of cut at 40 mm. Using this cutting condition, a mirror-like surface of 0.106 μm was produced. For machining under cryogenic condition at VBmax of 0.2 mm, the maximum tool life of 1864 min was achieved at a cutting speed of 900 m/min, feed rate of 0.02 mm/tooth, axial depth of cut of 0.3 mm, and radial depth of cut of 40 mm. Under this cutting condition, a lower surface finish of 0.091 μm was obtained. It can be concluded that the application of liquid nitrogen (LN2) is very effective in enhancing the tool life and in obtaining a better-machined surface, especially at a lower cutting speed of 900 m/min. A longer tool life and high-quality machined parts will significantly improve the productivity and cost savings in the related industry.

Milling machinability analysis of GW63K rare-earth magnesium alloys based on the concept of clean cutting

Comparative Study on Milling Performances of Rare-earth Magnesium Alloys under Dry and MQL Conditions

An Investigation on Tool Performances in Milling Rare-Earth Magnesium Alloys

Wear Behavior of Different Coated Tools in MQL-assisted Milling of Magnesium-Based Rare-Earth Alloys

Wear behavior of different coated tools in MQL-assisted high-speed milling of magnesium-based rare-earth alloys

Machinability analysis in high-speed milling of AlSi7Mg alloys under EMQL conditions: An approach toward sustainable manufacturing

Characterization of cast rare earth WE43 magnesium alloy and parameter optimization for wire electrical discharge machining using TOPSIS & COPRAS

Experimental Study and Parameter Optimization on Sustainable and Efficient Machining GH4169 with Rotating Short Arc Milling Method

Characteristics and Surface Serviceability for Cryogenic Milling Mg-1.6Ca-2.0Zn Medical Magnesium Alloy

Sustainable High-Speed Milling of Magnesium Alloy AZ91D in Dry and Cryogenic Conditions

Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy

Analysis of cutting forces and surface quality during micro milling of AZ31B magnesium alloy

Study of machining performance for electrochemical grinding of difficult-to-cut alloy U71Mn

Microstructure and Mechanical Properties of Laser Melting Deposited GW103K Mg-RE Alloy

Environmental, Economical and Technological Analysis of MQL-Assisted Machining of Al-Mg-Zr Alloy Using PCD Tool

Machinability Investigations based on Tool Wear, Surface Roughness, Cutting Temperature, Chip Morphology and Material Removal Rate during Dry and MQL-Assisted Milling of Nimax Mold Steel

Ultra-precision micro-cutting of maraging steel 3J33C under the influence of a surface-active medium

A Comparison of Dry and Wet Machining of SiC Particle-Reinforced Aluminum Metal Matrix Composites

Machining-induced residual stress analysis and multi-objective optimization for milling process of Mg–Li alloy

Effect of cooling and lubrication conditions on the variable angle milling of unidirectional CFRP with PCD Tools

Experimental examination on electrochemical machining of Mg/FeCoCrNiMn composite