Abstract:Magnesium alloys are lightweight structural materials with excellent machinability. However, further development is seriously limited by their low strength and poor formability. Therefore, further decreasing the surface residual stress of the frame by post-process treatment is a key issue, such as for reducing the subsequent deformation due to the residual stress, improving the machining accuracy and corrosion resistance of the magnesium alloy frame products, and extending the service life of the magnesium alloy frame products. Using AZ31B magnesium alloy as the experimental subject, and by exploring the effects of milling parameters on the surface quality of frame parts, this study shows that the surface residual compressive stress, hardness, and roughness of frame parts decreased with the increasing of the milling speed and increased as the depth of cut and the feed per tooth increased. Using cutting fluid in the milling process can decrease the surface residual stress and roughness of the frame parts but increase the surface hardness. In accordance with the experimental results and analysis, the main reason affecting the residual stress on the surface layer of frame components is the thermal elastoplastic problem caused by thermal mechanical coupling during the milling process, resulting in varying stress states on the workpiece's surface. The primary contributors to hardness are the work-hardening effect induced by milling forces and the thermal-softening effect of milling temperatures, which either augment or diminish the workpiece's surface hardness. Furthermore, the primary factor impacting surface roughness is the magnitude of cutting forces. Excessive cutting forces lead to the ploughing phenomenon or tool vibrations, thereby causing varying degrees of surface roughness on the workpiece. Meanwhile, the influence of stress-relief annealing or cryogenic treatment on surface residual stress and hardness after the milling of the frame parts was researched. It shows that within the selected milling parameters, both stress-relief annealing and cryogenic treatment can reduce the surface residual stress and homogenize the residual stress distribution of frame parts. Stress-relief annealing leads to a reduction in the hardness of the machined surface, and the hardness of the machined surface increases slightly under cryogenic treatment. The effects of the two post-processing methods on surface quality vary, and in practical production, a rational selection can be made according to the different processing requirements to achieve the optimal standards.

Comparative Study on Milling Performances of Rare-earth Magnesium Alloys under Dry and MQL Conditions

Milling machinability analysis of GW63K rare-earth magnesium alloys based on the concept of clean cutting

Wear behavior of different coated tools in MQL-assisted high-speed milling of magnesium-based rare-earth alloys

Effect of MQL condition on cutting performance of high-speed machining of GH4099 with ceramic end mills

Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy

Experimental Study on Surface Microscopic Characteristics of scCO2-MQL Milled γ-TiAl Alloy

Characteristics and Surface Serviceability for Cryogenic Milling Mg-1.6Ca-2.0Zn Medical Magnesium Alloy

Study on High-Speed Machining of 2219 Aluminum Utilizing Nanoparticle-Enhanced Minimum Quantity Lubrication (MQL) Technique

Sustainable High-Speed Milling of Magnesium Alloy AZ91D in Dry and Cryogenic Conditions

Analysis of cutting forces and surface quality during micro milling of AZ31B magnesium alloy

Comparative analysis and experimental exploration of the milling process in the machining of Inconel 825 material under MQL

Machinability Investigations based on Tool Wear, Surface Roughness, Cutting Temperature, Chip Morphology and Material Removal Rate during Dry and MQL-Assisted Milling of Nimax Mold Steel

Investigation on cutting performance in ultrasonic assisted helical milling of Ti6Al4V alloy by various parameters and cooling strategies

MQL milling of TC4 alloy by dispersing graphene into vegetable oil-based cutting fluid

Surface Quality for Cryogenic Milling Mg-1.6Ca-2.0Zn Medical Magnesium Alloy

Optimizing dry milling of stir-cast and heat-treated AZ80 magnesium alloy using multiple criteria optimization technique: an experimental study

Effects of Quenching Cooling Rate on Residual Stress and Mechanical Properties of a Rare-Earth Wrought Magnesium Alloy

Environmental, Economical and Technological Analysis of MQL-Assisted Machining of Al-Mg-Zr Alloy Using PCD Tool

Mechanism, cutting performance, and tool wear of MQL milling aluminum alloys with dual-nozzle

Atmospheric pressure plasma jet and minimum quantity lubrication assisted micro-grinding of quenched GCr15

Study of Machined Surface Quality of AZ31B Magnesium Alloy by End Milling