Abstract:The development of one-part geopolymer mortars has greater potential than the traditional two-part mortars, especially in repair applications, to convert waste into useful beneficial products while simultaneously eliminating the hazards associated with the alkaline solutions. Nevertheless, the inherent brittleness exhibited by the one-part geopolymers displays drawbacks like OPC when subjected to flexural loading. The fibers selection as well as their strengthening effects from literature is considerably scarce, especially for the repairing geopolymer system. This work aims to investigate the influences of fiber types and volume fractions on the workability, physical behavior, and cracking/fatigue resistance of ambient air-cured one-part geopolymer mortar. Reaction kinetics, mineralogical phases, and elemental components were explored by means of the TAM, quantitative XRD, and EDS mapping analysis. The FESEM and X-CT were employed to compare the microstructures and pore characteristics of the fibers-reinforced products. The results show that the copper-plated steel fiber produced the least change in workability, while the basalt fiber produced the lowest flow values. Setting time was the shortest for the basalt fiber reinforced, followed by polyvinyl-alcohol fiber. The steel fiber and carbon fiber would improve the mechanical properties of mortar significantly, especially in the early stage. The fatigue strength of 1 vol% carbon fiber reinforced mortar under 2 million cycles loading was the highest (3.72 MPa). The fibers addition a substantial decrease in sphericity and compactness of the pores (high anisotropy) as evidenced by X-CT data. Moreover, three hydration heat processes occurred after water was added to the one-part geopolymer mortar, which included dissolution of Na2SiO3 particles, network degradation, and a second pozzolanic reaction. More crystalline formation occurred over curing time to form gel networks with high stability and generated different bonding modes with various fibers.

Mechanical Behaviors of Metakaolin-Based Foamed Geopolymer (MKFG) under Dynamics Loading

Compositional Dependence of Pore Structure, Strengthand Freezing-Thawing Resistance of Metakaolin-Based Geopolymers

Early-Stage Geopolymerization Process of Metakaolin-Based Geopolymer

Chemical–physical–mechanical Stability of MKG Mortars under Sulfate Attacks

Correlating the Elastic Properties of Metakaolin-Based Geopolymer with Its Composition

Influence of direct foaming methods on the early performance and microstructure of metakaolin‐based foam geopolymers

Orthogonal analysis and mechanism of compressive strength and microstructure of the metakaolin-fly ash geopolymer

Relation between drying shrinkage behavior and the microstructure of metakaolin-based geopolymer

Mechanical properties of metakaolin-based geopolymer with glass fiber reinforcement and vibration preparation

Performance Characteristics of Micro Fiber-Reinforced Ambient Cured One-Part Geopolymer Mortar for Repairing

Mechanical performance and hydration mechanism of geopolymer composite reinforced by resin

The Influence of Particle Size and Calcium Content on Performance Characteristics of Metakaolin- and Fly-Ash-Based Geopolymer Gels

Metakaolin-Based Geopolymer Features Different Pore Structure Characteristics from Ordinary Portland Cement Paste: A Mechanistic Study

Effects and Mechanisms of Surfactants on Physical Properties and Microstructures of Metakaolin-Based Geopolymer

Rate-Dependent Bonding of Steel Reinforcement in Geopolymer Concrete

Investigation of Setting Time and Microstructural and Mechanical Properties of MK/GGBFS-Blended Geopolymer Pastes

A Multiscale Investigation of Reaction Kinetics, Phase Formation, and Mechanical Properties of Metakaolin Geopolymers

Study on the Protective Performance of Metakaolin-Based Foam Geopolymer (MKFG) As a Sacrificial Cladding under Internal Blast Mitigation

Effects of Different Calcium Sources on Mechanical Properties of Metakaolin Geopolymers

Microstructure and mechanical properties of metakaolin-based geopolymer composites containing high volume of spodumene tailings

Experimental investigation on the anti-detonation performance of composite structure containing foam geopolymer backfill material