Abstract:High-pressure direct injection diesel/methanol dual-fuel engines exhibit excellent emission reduction potential, but they are still in the initial stage of research and development. The influences of different methanol injection locations, injection duration, and injection pressures on combustion characteristics, mixture homogeneity, and exhaust emissions are investigated to explore appropriate injection strategies and further optimize the engine performance base using CONVERGE software. The results show that the impact of the methanol injection position on the engine is relatively small, especially on combustion characteristics. A larger axial nozzle distance contributes to the formation of the homogeneous mixture, improving the engine economy. However, the engine performance is remarkably affected by methanol injection duration and methanol injection pressure. A shorter combustion duration is achieved with a decrease in the methanol injection duration and an increase in the methanol injection pressure, as a result of which the fuel economy is improved, with the combustion process more concentrated near the top dead center. Simultaneously, the mixture homogeneity is enhanced, which is conducive to a reduction in soot and CO emissions, yet not to a NOX and HC reduction. The lowest overall emissions of NOX, soot, CO, and HC are achieved when the radial nozzle distance and axial nozzle distance are 2.5 mm and 0.5 mm, respectively. Besides, the combustion characteristics and emissions of the engine are affected significantly under different methanol injection locations and injection pressures. The increased injection interval leads to deteriorating combustion characteristics and economy, i.e., a delayed combustion phase (CA50), an extended ignition delay and combustion duration (CA10–CA90), thereby increasing CO and soot emissions, but decreasing NOX emission. Additionally, the optimal economy and exhaust emissions are obtained when adopting an injection duration of 6 °CA and an injection pressure of 44.4 MPa. The ITE is increased in this case compared to the other injection strategies, thereby improving the engine performance significantly. The results provide parametric feedback and theoretical support for the design of high-pressure direct injection diesel/methanol dual-fuel engines from a time and space perspective, which has certain theoretical significance.

A Quasi-Dimensional Model of Multiple-Cycle Fuel Film Evaporation in a Port Fuel Injection Spark-Ignition Methanol Marine Engine

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Numerical Study of the Effect of Direct-Injection Timing of Methanol and Excess Air Ratio on the Combustion Characteristics of a Marine Diesel-Methanol Dual-Fuel Engine

Evaporate Prediction and Compensation of Intake Port Wall-Wetting Fuel Film for Spark Ignition Engines Fueled with Ethanol-Gasoline Blends

Impact of Pilot Injection on Combustion and Emission Characteristics of a Low-Speed Two-Stroke Marine Diesel Engine

Numerical study of injection strategies for marine methanol/diesel direct dual fuel stratification engine

Experimental Study on Combustion Characteristics of a Fischer‐tropsch Diesel/methanol Reactivity Controlled Compression Ignition Mode Engine

Research on Performance Matching of Intake and Exhaust Ports of Marine Medium Speed Dual Fuel Engine

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

Simulation Study on the Impact of Injection Strategies on the Performance of Methanol–Gasoline Dual-Fuel Engines

Simulation about the Effect of the Height-to-Stroke Ratios of Ports on Power and Emissions in an OP2S Engine Using Diesel/Methanol Blends

Investigation on efficient and clean combustion pre-injection strategy of a diesel/methanol dual direct-injection marine engine under full load

Influence of the Port Height to Stroke Ratio on the Performance of an OP2S Engine Fueled with Methanol/Diesel

A Reduced Combustion Kinetic Model for the Methanol-Gasoline Blended Fuels on SI Engines

Combustion model development of future DI engines for carbon emission reduction

A preliminary numerical study on the use of methanol as a Mono-Fuel for a large bore marine engine

Large-eddy simulation of the injection timing effects on the dual-fuel spray flame

Modeling and Experimental Validation of a Pure Methanol-Fueled Small SI Engine: Impact of the Laminar Flame Speed Correlation

Effects of Combustion Phasing, Injection Timing, Relative Air-Fuel Ratio and Variable Valve Timing on Si Engine Performance and Emissions Using 2,5-Dimethylfuran