Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Combustion model development of future DI engines for carbon emission reduction

Investigation on Spray Combustion Modeling for Performance Analysis of Future Low- and Zero-Carbon Di Engine

Prediction of Heat Release and Nox Emissions for Direct-Injection Diesel Engines Using an Innovative Zero-Dimensional Multi-Phase Combustion Model

Prediction of Pollutants Emissions and Performance of Direct Injection Diesel Engines with Quasi Dimensional Combustion Model

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Quasi-Dimension Modeling of Performance and Emissions for Direct Injection Diesel Engines

Multidimensional Computational Fluid Dynamics Combustion Process Modeling of a 6V150 Diesel Engine

Computational Modeling of Diesel Spray Combustion with Multiple Injections

Numerical Investigation on the Combustion and Emission Characteristics of Diesel Engine with Flexible Fuel Injection

A Transport Equation Residual Model Incorporating Refined G-Equation and Detailed Chemical Kinetics Combustion Models

Numerical Investigation of Combustion and Emission With Different Diesel Surrogate Fuel by Hybrid Breakup Model

Combustion Modelling for A Diesel Engine with Multi-Stage Injection Using A Stochastic Combustion Model

A Prediction of DI Diesel Engine Performance Using the Multizone Model

Simulation of Direct Injection Diesel Engine Combustion and Emission

Computational Fluid Dynamic Modelling a Heavy-Duty Compression-Ignition Engine Fuelled with Diesel and Gasoline-Like Fuels

Data-Driven Prediction of Key Combustion Parameters Based on an Intelligent Diesel Fuel Injector for Large Engine Applications

Realistic fuel spray modeling for gasoline direct injection engine applications

Quasi-Dimensional Multizone Combustion Model for Direct Injection Engines Fuelled with Dimethyl Ether

A Study on the Effect of Injection Rate on Emission Characteristics in D.I. Diesel Engine by Multi-zone Model

Parametric study of the impact of EGR and fuel properties on diesel engine performance using a predictive thermodynamic model

Development and Validation of a Quasi-Dimensional Combustion Model for SI Engines Fuelled by HCNG with Variable Hydrogen Fractions