Abstract:Ultra-low-power (ULP) crystal oscillators (X0s) [1–5] are essential in wirelessly linked loT nodes: for time-keeping purposes, they need to consume low power since they stay always-on and remain accurate to reduce synchronization guard time [6]. In recent years, pulse-injection-based X0s (PIX0s) have gained attention for their nW-level low power with good frequency stability. Typically implemented with a classic pierce oscillator for startup, these designs aim to take over the established parallel oscillation and replenish only the energy loss in the crystal by injecting short current pulses at the oscillating nodes' voltage peaks and valleys. They promise lower power consumption since they don't rely on a small-signal negative resistance that requires a high static bias current, seen as the crossbar current in the inverter. Yet to design these PIX0s, the designers must face two challenges, as shown in Fig. 3.8.1. The first is the timing control for the injected current pulses. Setting the rising zero-crossing point of the oscillating waveform as the $0^\circ$ phase reference (or 0 in time), this scheme requires a positive current push at $90^{\circ}$ (or T/4) and a negative current pull at $270^{\circ}$ (or 3T/4). Misalignments in timing create an orthogonal current component disrupting the phase, translating noise in the circuit to jitter while reducing the energy efficiency to maintain the same oscillation amplitude. The second challenge is oscillation amplitude control. For ultra-low-power operation, the oscillation amplitude needs to be low but stable since a linear increase in the oscillation amplitude leads to quadratic power consumption to compensate for the loss in the crystal.

A 0.72nw, 0.006mm2 32khz Crystal Oscillator with Adaptive Sub-Harmonic Pulse Injection from −40°C to 125°C in 22nm FDSOI

An Adaptive Sub-Harmonic Pulse Injection Crystal Oscillator Achieving -40° C to 125° C Operation

A 60GHz voltage-controlled oscillator with a 3.6GHz tuning range in 180nm CMOS technology

A 43 nW, 32 kHz, ±4.2 ppm Piecewise Linear Temperature-Compensated Crystal Oscillator With ΔΣ-Modulated Load Capacitance

Design of a Crystal Oscillator Chip with High Stability and Wide Power Supply Range

3.8 A 0.954nw 32khz Crystal Oscillator in 22nm CMOS with Gm-C-Based Current Injection Control

A Digital-Analog Mixed Temperature Compensated Crystal Oscillator with 1.8v/0.18&#x03bc;m Mix-Signal CMOS Process

A High-Precision Mixed-Signal Voltage-Controlled Crystal Oscillator with Temperature Compensation

A 0.07-Ppm/step Differential Digitally Controlled Crystal Oscillator with Guaranteed Monotonicity

Design of a New Analog TCXO with High Frequency Stability

Design of TCXO Chip with High Accuracy and Wide Temperature Range

A 0.1 ppm Successive Approximation Frequency-Temperature Compensation Method for Temperature Compensated Crystal Oscillators (TCXO)

A Non-trimmed, 7 MHz and 52 Ppm/°c Relaxation Oscillator with Loop Errors Compensation from -40°C to 165°C

A 9.4 MHz, 0.011 Mm², 107.6 Ppm/°c Single-Port RC Oscillator with Temperature Compensation

Design of Crystal Oscillator Chip with Low Power and High Stability

A Low Temperature Drift Coefficient Crystal-Less Frequency Reference Clock Compensated By Temperature Sensor For Microsystem

Low-phase-noise surface acoustic wave oscillator using phononic crystal bandgap-edge mode

A Low-Phase-noise Digitally Controlled Crystal Oscillator for DVB TV Tuners

A 8.1-nW, 4.22-kHz, −40–85 °C relaxation oscillator with subthreshold leakage current compensation and forward body bias buffer for low power IoT applications

A 27.6 MHz 297 Μw 33 Ppm/°c CMOS Relaxation Oscillator with an Adjustable Temperature Compensation Scheme

A 0.6V 50-to-145mhz PVT Tolerant Digital PLL with DCO-dedicated ΔΣ LDO and Temperature Compensation Circuits in 65nm CMOS