Abstract:To explore room-temperature strengthening and high-temperature ductility, a lightweight novel Mg-1.85Gd-0.64Al-0.62Zn alloy was fabricated by innovative multidirectional forging and a hot-rolling technique. Microstructures and mechanical properties were studied at room and elevated temperatures with an optical microscope, an X-ray diffractometer, and a tensile tester. An ultimate tensile strength of 260 MPa, yield strength of 171 MPa, and elongation of 20.4% were demonstrated at room temperature. The room-temperature strengthening mechanisms were identified by strengthening the model estimation. A type C Portevin-Le Chatelier effect was discovered and elucidated in this alloy. X-ray diffraction analysis revealed that the phase composition is α-Mg solid solution and (Mg, Al)3Gd, Al7Zn3, and Al2Gd intermetallic compounds. Examination of the microstructure at elevated temperatures revealed that dynamic recrystallization and dynamic grain growth occur. In particular, it was discovered that bimodal microstructures or incomplete dynamic recrystallization microstructures exist in high-temperature deformation. A maximum quasi-superplasticity of 228.4% was demonstrated in this alloy at 673 K and 5.0 × 10-4 s-1. Flow stress curves showed that the present alloy exhibits Sotoudeh-Bate curves or a long intermediate strain-hardening stage followed by a strain-softening stage. A modified Zerilli-Armstrong constitutive equation incorporating the number of dislocations was established. The power-law constitutive equation was established to identify the deformation mechanism. Both constitutive models had good predictability. At 673 K and 5.0 × 10-4 s-1, the stress exponent was 4, and the average deformation activation energy was 104.42 kJ/mol. The number of dislocations inside a grain was 146. This characteristic evidence confirmed that dislocation motion controlled by pipe diffusion dominates the rate-controlling process under this condition.

A Novel Method Simultaneously Eliminating Portevin-Le Chatelier Effect and Enhancing Strength in Non-Heat-treatable Al-Mg Alloys

The Portevin-Le Chatelier Effect in Al-Mg Alloy Investigated by Infrared Pyrometry

Enhancing the strength and sensitization resistance of 5xxx alloys via nanoscale clustering induced by room-temperature cyclic plasticity

A Critical Review on the Portevin-Le Chatelier Effect in Aluminum Alloys

Precipitation strengthening of aluminum alloys by room-temperature cyclic plasticity

Room-Temperature Strengthening, Portevin-Le Chatelier Effect, High-Temperature Tensile Deformation Behavior, and Constitutive Modeling in a Lightweight Mg-Gd-Al-Zn Alloy

Enhanced Plastic Stability: Achieving High Performance in a Al6xxx Alloy Fabricated by Additive Manufacturing

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

An Mg‐Al‐Zn Alloy with Verry High Specific Strength and Superior High‐strain‐rate Superplasticity Processed by Reciprocating Extrusion

Synergistic Mechanism of Strengthening and Toughening of Tissue Regulation Response to Mg/Al Composite Laminates by Hard Plate Accumulative Roll Bonding

Characterization of Portevin–Le Chatelier Effect in Aluminum Alloy AA5052 under Strain-Controlled Tensile Test Via Digital Image Correlation and Acoustic Emission

Achieving superior dispersion-strengthening effect in an AA5xxx Al-Mg-Mn alloy by mico-alloying

Enhancing Plasticity in BCC Mg-Li-Al Alloys Through Controlled Precipitation at Grain Boundaries

The Portevin-Le Chatelier (PLC) effect in an Al-Cu aluminum alloy fabricated by selective laser melting

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Deformation mechanisms and mechanical properties of the high-strength and ductile Al-Zn-Mg-Cu alloys processed by repetitive continuous extrusion forming process with different heat treatments

Enhancing Plasticity in Laser Additive Manufactured High-Entropy Alloys: the Combined Effect of Thermal Cycle Induced Dissolution and Twinning

Enhanced Mechanical Properties in 6082 Aluminum Alloy Processed by Cyclic Deformation

Microstructure and mechanical properties synergistically enhanced via heat treatment modification of the as-extruded Mg-1.5Al-0.5Zn-0.2Y-0.2Ca alloy

On the spatio-temporal characteristics of the Portevin-Le Chatelier effect in aluminium alloy AA5182: An experimental and numerical study

Fracture behavior of a rapidly solidified thin-strip continuous cast AA5182 Al-Mg alloy with the Portevin-Le Chatelier effect under varying strain rates