Papertronics: Integrating Electronics and Microfluidics on Paper for Sustainable Electroanalysis

Lingyin Meng,Danfeng Cao,Jonas Oshaug Pedersen,Grzegorz Greczynski,Vladyslav Rogoz,Warakorn Limbut,Mats Eriksson

DOI: https://doi.org/10.26434/chemrxiv-2024-6pclv

2024-08-20

Abstract:The widespread use of non-renewable materials in point-of-care (PoC) electroanalysis, such as disposable test strips with electronic meters, has inadvertently contributed to electronic waste. Paper, traditionally used as a passive substrate, offers a renewable alternative but faces limitations in direct conversion into conductive electronic components, hindering its adoption for on-site analysis. Here, we present the development of papertronics, integrating conductive electronic components and microfluidics on a single sheet of paper for sustainable electroanalysis. Using a flame retardant and laser treatment, we enable a direct conversion of cellulose paper into laser-induced graphite (PLIG). By optimizing laser parameters (e.g., laser power, scan speed and defocus/focus), the physicochemical properties of the PLIG are tailored. Microfluidic channels are patterned with sub-millimetre resolution via hot-pressing hydrophobic parafilm into paper at a relatively low temperature of 60 °C for 15 seconds. This process facilitates a seamless integration of paper-based electronic components with microfluidics. Demonstrative applications in pH sensing showed a sensitivity of -40.3 mV pH-1, and lactate biosensing achieved a sensitivity of 0.92 μA mM-1. This study establishes a foundation for cost-effective, environmentally friendly electroanalytical platforms with broad implications in biomedical diagnostics and environmental monitoring.

Chemistry

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is the e - waste problem caused by the widespread use of non - renewable materials in current point - of - care (PoC) electroanalysis. Specifically, traditional PoC test strips are usually made of non - renewable materials such as metals and carbon allotropes, and these materials will inadvertently generate a large amount of e - waste after being used in large quantities. Therefore, the paper proposes a sustainable solution, that is, integrating conductive electronic components and microfluidic technology into a single piece of paper through paper - based technology (papertronics) to achieve sustainable electroanalysis. This method not only reduces the impact on the environment, but also reduces costs and improves portability and on - site analysis capabilities.

### Background and Problems of the Paper
1. **E - waste Problem**: Although traditional PoC electroanalysis devices (such as disposable test strips and electronic meters) have made revolutionary progress in disease diagnosis and health management, these devices are usually made of non - renewable materials, resulting in the accumulation of a large amount of e - waste.
2. **Advantages of Paper - based Materials**: As a renewable material, paper has the advantages of low cost, biodegradability, good biocompatibility, passive capillary infusion and high flexibility. However, at present, paper is mainly used as a passive substrate and is difficult to be directly converted into conductive electronic components, which limits its application in electroanalysis.

### Solutions
1. **Preparation of Paper - based Electronic Components**: Through flame retardant treatment and laser processing technology, the paper directly converts ordinary paper into laser - induced graphite (PLIG), achieving efficient, low - cost and mask - free preparation of paper - based electronic components.
2. **Preparation of Microfluidic Channels**: By hot - pressing method, hydrophobic Parafilm is patterned on the paper base to form microfluidic channels, realizing the seamless integration of paper - based electronic components and microfluidic technology.
3. **Application Demonstration**: The paper shows the application of pH sensors and lactate biosensors based on this technology, achieving sensitivities of - 40.3 mV pH\(^{-1}\) and 0.92 μA mM\(^{-1}\) respectively.

### Main Contributions
1. **Sustainability**: By using renewable materials (paper) and environmentally - friendly preparation methods, the generation of e - waste is reduced.
2. **Versatility**: The integration of paper - based electronic components and microfluidic technology is realized, expanding the application of paper - based technology in biomedical diagnosis, environmental monitoring and other fields.
3. **Low Cost**: The preparation method is simple and low - cost, which is suitable for large - scale production and practical application.

In conclusion, this paper aims to solve the e - waste problem brought by traditional PoC electroanalysis devices by developing an integrated system of paper - based electronic components and microfluidic technology, and provides a sustainable, economic and efficient solution.