Abstract:The interfacial contact between a solid electrolyte and cathode materials is one of the challenges for the solid-state battery (SSB) industry. The cosintering of a solid electrolyte and cathode materials could be a possible solution. Considering the future scope of solid-state battery fabrication by the cosintering process of phosphate-based solid electrolytes and phosphate-based cathodes (LiFePO4, Li3V2(PO4)3, etc.), the present study focuses on stabilizing the NASICON structured Li1.4Al0.4Ti1.6(PO4)3 (LATP) solid electrolyte in an inert atmosphere as proposed cathode materials are not stable in air at high temperatures. The results show a high influence of particle size and heating rate along with sintering temperature on achieving a pure phase and fully dense pellets in an argon atmosphere. Cracks/voids, secondary phases, and reduction of Ti were observed in pellets prepared with a powder of bigger size under argon gas sintering. The present work not only successfully solves these issues by decreasing the particle size and reducing the heating rate but also produces highly dense pellets with more than 98% density at 800 °C. We have also achieved a high conductivity of 8.77 × 10–4 S cm–1 at room temperature for the pellet sintered at just 800 °C in argon, which is 3–4 times higher than the conductivity of samples sintered at higher than 800 °C. Therefore, we succeeded in obtaining for the first time a high conductivity, pure phase, and high density of the LATP solid electrolyte at a relatively low temperature of 800 °C in an argon atmosphere, which is an important solution for solid-state battery fabrication by cosintering process. Furthermore, the stabilized NASICON electrolyte in an argon atmosphere also shows superior electrochemical performance when tested with Li metal in a symmetric battery cell.

Cold-sintering assisted process enables densified and robust fine-grained Li1.3Al0.3Ti1.7(PO4)3 electrolytes for solid-state batteries

Aqueous Tape Casting Phosphate Ceramic Electrolyte Membrane for High Performance All Solid-State Lithium Metal Battery

Microstructure and ionic conductivities of NASICON-type Li1.3Al0.3Ti1.7(PO4)3 solid electrolytes produced by cold sintering assisted process

Insight into the Microstructure and Ionic Conductivity of Cold Sintered NASICON Solid Electrolyte for Solid-State Batteries

Optimization of sintering process on Li1+Al Ti2-(PO4)3 solid electrolytes for all-solid-state lithium-ion batteries

Cold-sintering Assisted Process Enables Densified and Robust Fine-Grained Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 Electrolytes for Solid-State Batteries

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Enabling long-term oxide based solid-state lithium metal battery through a near room-temperature sintering process

Low-temperature fabrication of NASICON-type LATP with superior ionic conductivity

Cold Sintering of Halide-in-Oxide Composite Solid-State Electrolytes

High Li+ Conductivity of Li1.3+xAl0.3−xMgxTi1.7(PO4)3 with Hybrid Solid Electrolytes for Solid‐State Lithium Batteries

High Ionic Conductive Sodium Β-Alumina (SBA) and SBA-NaPF6 Composite Solid Electrolytes Prepared by Cold Sintering Process

Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte fabricated from bimodal powder precursor

Densification of a NASICON-Type LATP Electrolyte Sheet by a Cold-Sintering Process

Interface Welding Via Thermal Pulse Sintering to Enable 4.6 V Solid‐State Batteries

Two-step sintering technique of LATP ceramic electrolyte with enhanced key parameters

Stabilizing the NASICON Solid Electrolyte in an Inert Atmosphere as a Function of Physical Properties and Sintering Conditions for Solid-State Battery Fabrication

Achieving High Ionic Conductivity of LATP Solid Electrolyte Via LiTFSI-assisted Cold Sintering Process

Facile Route to Synthesize a Highly Sinterable Li1.3Al0.3Ti1.7(PO4)3 Solid Electrolyte

Hybrid solid state electrolytes blending NASICON-type Li1+xAlxTi2–x(PO4)3 with poly(vinylidene fluoride-co-hexafluoropropene) for lithium metal batteries

Reduced Sintering Temperatures of Li+ Conductive Li1.3Al0.3Ti1.7(PO4)3 Ceramics