Abstract:Solid-state batteries (SSBs) with Li-ion conductive electrolytes made from polymers, thiophosphates (sulfides) or oxides instead of liquid electrolytes have different challenges in material development and manufacturing. For oxide-based SSBs, the co-sintering of a composite cathode is one of the main challenges. High process temperatures cause undesired decomposition reactions of the active material and the solid electrolyte. The formed phases inhibit the high energy and power density of ceramic SSBs. Therefore, the selection of suitable material combinations as well as the reduction of the sintering temperatures are crucial milestones in the development of ceramic SSBs. In this work, the co-sintering behavior of Li1.3Al0.3Ti1.7(PO4)3 (LATP) as a solid electrolyte with Li-ion conductivity of ≥0.38 mS/cm and LiFePO4 with a C-coating (LFP) as a Li-ion storage material (active material) is investigated. The shrinkage behavior, crystallographic analysis and microstructural changes during co-sintering at temperatures between 650 and 850 °C are characterized in a simplified model system by mixing, pressing and sintering the LATP and LFP and compared with tape-casted composite cathodes (d = 55 μm). The tape-casted and sintered composite cathodes were infiltrated by liquid electrolyte as well as polyethylene oxide (PEO) electrolyte and electrochemically characterized as half cells against a Li metal anode. The results indicate the formation of reaction layers between LATP and LFP during co-sintering. At Ts > 750 °C, the rhombohedral LATP phase is transformed into an orthorhombic Li1.3+xAl0.3−yFex+yTi1.7−x(PO4)3 (LAFTP) phase. During co-sintering, Fe3+ diffuses into the LATP phase and partially occupies the Al3+ and Ti4+ sites of the NASICON structure. The formation of this LAFTP leads to significant changes in the electrochemical properties of the infiltrated composite tapes. Nevertheless, a high specific capacity of 134 mAh g−1 is measured by infiltrating the sintered composite tapes with liquid electrolytes. Additionally, infiltration with a PEO electrolyte leads to a capacity of 125 mAh g−1. Therefore, the material combination of LATP and LFP is a promising approach to realize sintered ceramic SSBs.

Cold Sintering of Halide-in-Oxide Composite Solid-State Electrolytes

Ionic Liquid Reinforced NaSICON-type Oxide Electrolyte Films Enabling Solid State Conversion Metal Fluoride-Lithium Batteries

Cold Sintering Halide-in-Oxide Composite Solid-State Electrolytes with Enhanced Ionic Conductivity

Insight into the Microstructure and Ionic Conductivity of Cold Sintered NASICON Solid Electrolyte for Solid-State Batteries

Cold-sintering assisted process enables densified and robust fine-grained Li1.3Al0.3Ti1.7(PO4)3 electrolytes for solid-state batteries

Microstructure and ionic conductivities of NASICON-type Li1.3Al0.3Ti1.7(PO4)3 solid electrolytes produced by cold sintering assisted process

Probing Cold Sintering-Regulated Interfaces and Integration of Polymer-in-Ceramic Solid-State Electrolytes

Hydroflux-Assisted Cold Sintering: Eutectic Mixtures for Boosting Ionic Conductivity in LATP Solid-State Electrolytes

Co-Sintering of Li1.3Al0.3Ti1.7(PO4)3 and LiFePO4 in Tape-Casted Composite Cathodes for Oxide Solid-State Batteries

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Reduced Sintering Temperatures of Li+ Conductive Li1.3Al0.3Ti1.7(PO4)3 Ceramics

Enabling long-term oxide based solid-state lithium metal battery through a near room-temperature sintering process

Achieving High Ionic Conductivity of LATP Solid Electrolyte Via LiTFSI-assisted Cold Sintering Process

Cold Sintering of Li6.4La3Zr1.4Ta0.6O12/PEO Composite Solid Electrolytes

Optimization of sintering process on Li1+Al Ti2-(PO4)3 solid electrolytes for all-solid-state lithium-ion batteries

Facile Route to Synthesize a Highly Sinterable Li1.3Al0.3Ti1.7(PO4)3 Solid Electrolyte

Stabilizing the NASICON Solid Electrolyte in an Inert Atmosphere as a Function of Physical Properties and Sintering Conditions for Solid-State Battery Fabrication

Hybrid solid state electrolytes blending NASICON-type Li1+xAlxTi2–x(PO4)3 with poly(vinylidene fluoride-co-hexafluoropropene) for lithium metal batteries

Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte fabricated from bimodal powder precursor

Li-Ion Conductive Li1.3Al0.3Ti1.7(PO4)3 (LATP) Solid Electrolyte Prepared by Cold Sintering Process with Various Sintering Additives

High Li+ Conductivity of Li1.3+xAl0.3−xMgxTi1.7(PO4)3 with Hybrid Solid Electrolytes for Solid‐State Lithium Batteries