Abstract:The highly reactive chemical nature of aluminum makes it production energy-intensive or essentially impossible to extract alloying elements from Al-based liquids. Using molten salt fluxing and electrolysis processes can effectively refine coarse Al scraps. However, the generation of toxic gases and hazardous dross during these processes can cause significant environmental protection challenges and result in notable social concerns. Therefore, the primary recycling of post-consumer Al in industries currently proceeds mainly in a cascade manner, which is not sustainable when considering the Al cycle trends in the coming decades. Herein, we develop a novel process to separate primary Al from the crystallizing liquid when a constant electromagnetic force (EMF) is applied. Using this technique, we successfully upgraded Al–7mass%Si (hereafter, unless specified otherwise) alloy to approximately Al–3.6%Si in directional solidification. The separation mechanism was discussed in terms of the electrical properties of the respective phases during solidification. Fluid flow simulation results were applied to elucidate the separation behavior in the alloy. The upper and lower limits to separate the crystallizing alloy into an Al-rich and Si-rich areas were determined when the controlling factors were clarified, which made it possible to scale up the present laboratory-based setup to an industrial level. Moreover, the energy consumption of the process was slightly higher than that required for remelting only. Using the EMF technique to separate the crystallizing alloy into Al-rich and Si-rich regions did not produce hazardous dross or toxic gases. This energy-saving and eco-friendly process can provide a breakthrough to overcome the "dead metal" crisis and thus realize sustainability by upgrading recycling of post-consumer hypoeutectic Al–Si casting alloys.

Electrochemical Reduction of Al(III) and Si(IV) in the NaF-AlF3-Al2O3-SiO2 Molten Salt System and Preparation of Homogeneous Al-Si Alloys by Molten Salt Electrolysis

Revealing Salt-Expedited Reduction Mechanism for Hollow Silicon Microsphere Formation in Bi-Functional Halide Melts

Impurity Behavior in Aluminum Extraction by Low-Temperature Molten Salt Electrolysis

Electrochemical behavior of silicon compound in LiF–NaF–KF–Na<sub>2</sub>SiF<sub>6</sub> molten salt

Electrochemical behavior of silicon compound in LiF–NaF–KF–Na 2 SiF 6 molten salt

Effects Of Electrolytic Parameters On The Deposition Of Boron At The Cathode During Molten Salt Electrolysis Of Silicon

Electrochemical behavior of Zr(IV) and co-reduction synthesis of Al-Zr alloys in KF-AlF3-Al2O3-ZrO2 molten salt

Electrochemical Behavior of Silicon in the (Nacl-Kcl-naf-sio 2 ) Molten Salt

A Low Temperature Molten Salt Process for Aluminothermic Reduction of Silicon Oxides to Crystalline Si for Li-ion Batteries

Upgrading recycling of Al–7 wt%Si alloys using electromagnetic force in directional solidification

Clean separation of vanadium from NaVO3 in NaF-KF-AlF3 molten salt by electrochemical reduction

Studies On Synthesis Mechanism Of Fe-Si Alloy

Separation of Al-Si-Fe-(Mn/Cr) melts for simultaneous recycle of Al-Si scraps and purification of silicon

Recovery of aluminum from waste aluminum alloy by low-temperature molten salt electrolysis

Microstructure and mechanical properties of as casted Al-Si-Sc-Ce alloys prepared by molten salt electrolysis with varied cooling rate

Enhancing the separation of Fe/Al/Ca impurities from metallurgical silicon to purify by slagging-directional solidification

Silicon prepared by electro-reduction in molten salts as new energy materials

Integrating preparation of borides and separation of alkaline- and rare-earth ions through an electrochemical alloying approach in molten salts

Investigation on Structures of Aluminum Melts Containing Small Amount of Silicon Element

Molecular Dynamics Investigation on Structural and Transport Properties of Na3AlF6–Al2O3 Molten Salt

Effect of Si Content on the Morphology Evolution of the Si Primary Dendrites in Al-Si Alloy Solvent Refining Process