Abstract:<div class="section abstract"><div class="htmlview paragraph">Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode. The findings demonstrate that ammonia-PODE3 mode exhibits better ignition characteristics than ammonia-diesel mode, resulting in an earlier ignition start, a larger flame area, a larger flame expansion speed, a shorter ignition delay time (IDT) and a shorter combustion duration (CD) due to the higher cetane number (CN) and a greater injection mass of PODE3 at the same energy input. Ammonia-PODE3 mode achieves larger maximum cylinder pressure (Pmax) and peak heat release rate (HRR) compared to ammonia-diesel mode. Furthermore, almost no soot was observed in ammonia-PODE3 mode throughout the entire combustion process. The results also indicate the start of the ignition is delayed and the first peak flame expansion speed decreases at a higher ammonia energy ratio. The maximum flame area is the largest at ERa = 60%, but the peak cylinder pressure and IMEP reach their highest values at ERa = 50%. Both the first peak flame area and the first peak flame expansion speed increase with the increase of ERInj1, and the Pmax and first peak HRR also increase. The IDT slightly extends with the increase of ERInj1, while CA50 advances and CD reduces. The start of the ignition is delayed with the advancement of the main injection time, and the largest flame area is observed at SOI1 = -12.5 °CA. Both the first Pmax and the maximum IMEP occur at SOI1 = -15 °CA. This is because the cylinder temperature and pressure are lower during combustion when the main injection time is early, while a later main injection time leads to inadequate fuel-air mixing and a delayed combustion phase.</div></div>

Combustion Characteristics and Flame Development of Ammonia in an Optical Spark-Ignition Engine

Numerical Investigation of a Heavy Duty Compression Ignition Engine Converted to Ammonia Spark Ignition Operation

Combustion of Premixed Ammonia and Air Initiated by Spark- Ignited Micro-gasoline-jet in a Constant Volume Combustible Vessel

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Understanding the difference in combustion and flame propagation characteristics between ammonia and methane using an optical SI engine

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Numerical Investigation of the Effect of Ammonia Addition on the Performance of a Stoichiometric Operated Natural Gas Spark Ignition Engine

Hydrogen Enriched Ammonia Engines: Assessment of Hydrogen Concentration in the Fuel Feed from the Laminar Flame Speed Viewpoint

Combustion Analysis of Ammonia Fueled High Compression Ratio SI Engine with Glow Plug and Sub-Chamber

Combustion and Emission Characteristics of a Spark Ignition Engine Fueled with Ammonia/gasoline and Pure Ammonia

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Experimental Study on Ammonia-Methanol Combustion and Emission Characteristics in a Spark Ignition Engine

An optical study of the combustion and flame development of ammonia-diesel dual-fuel engine based on flame chemiluminescence

Nitrogen Oxides Emission Characteristics of Zero-Carbon Ammonia-Hydrogen Fuels for Internal Combustion Engines

Preliminary assessment of the potential for rapid combustion of pure ammonia in engine cylinders using the multiple spark ignition strategy

Combustion and Emission Characteristics of an Ammonia-Hydrogen Engine under Passive- and Active-Jet Ignition

Optical diagnostic study on ammonia-diesel and ammonia-PODE dual fuel engines

Combustion Behaviors and Unregular Emission Characteristics in an Ammonia–Diesel Engine

Auto-Ignition and Flame Characteristics of Ammonia Reactivity-Controlled Compression Ignition Combustion in Comparison with Methane

Effects of intake parameters and compression ratio on ammonia combustion and emissions in SI engines

Characteristics of ammonia premixture combustion ignited by a gasoline ignition chamber