Abstract:<div class="section abstract"><div class="htmlview paragraph">Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode. The findings demonstrate that ammonia-PODE3 mode exhibits better ignition characteristics than ammonia-diesel mode, resulting in an earlier ignition start, a larger flame area, a larger flame expansion speed, a shorter ignition delay time (IDT) and a shorter combustion duration (CD) due to the higher cetane number (CN) and a greater injection mass of PODE3 at the same energy input. Ammonia-PODE3 mode achieves larger maximum cylinder pressure (Pmax) and peak heat release rate (HRR) compared to ammonia-diesel mode. Furthermore, almost no soot was observed in ammonia-PODE3 mode throughout the entire combustion process. The results also indicate the start of the ignition is delayed and the first peak flame expansion speed decreases at a higher ammonia energy ratio. The maximum flame area is the largest at ERa = 60%, but the peak cylinder pressure and IMEP reach their highest values at ERa = 50%. Both the first peak flame area and the first peak flame expansion speed increase with the increase of ERInj1, and the Pmax and first peak HRR also increase. The IDT slightly extends with the increase of ERInj1, while CA50 advances and CD reduces. The start of the ignition is delayed with the advancement of the main injection time, and the largest flame area is observed at SOI1 = -12.5 °CA. Both the first Pmax and the maximum IMEP occur at SOI1 = -15 °CA. This is because the cylinder temperature and pressure are lower during combustion when the main injection time is early, while a later main injection time leads to inadequate fuel-air mixing and a delayed combustion phase.</div></div>

Understanding the difference in combustion and flame propagation characteristics between ammonia and methane using an optical SI engine

Numerical Investigation of a Heavy Duty Compression Ignition Engine Converted to Ammonia Spark Ignition Operation

Combustion of Premixed Ammonia and Air Initiated by Spark- Ignited Micro-gasoline-jet in a Constant Volume Combustible Vessel

Numerical Investigation of the Effect of Ammonia Addition on the Performance of a Stoichiometric Operated Natural Gas Spark Ignition Engine

Auto-Ignition and Flame Characteristics of Ammonia Reactivity-Controlled Compression Ignition Combustion in Comparison with Methane

Comparative study on combustion and flame characteristics of NH 3 dual-fuel engine under CI vs SI combustion modes

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Hydrogen Enriched Ammonia Engines: Assessment of Hydrogen Concentration in the Fuel Feed from the Laminar Flame Speed Viewpoint

Effects of intake parameters and compression ratio on ammonia combustion and emissions in SI engines

An optical study of the combustion and flame development of ammonia-diesel dual-fuel engine based on flame chemiluminescence

Combustion Analysis of Ammonia Fueled High Compression Ratio SI Engine with Glow Plug and Sub-Chamber

Experimental Study on Ammonia-Methanol Combustion and Emission Characteristics in a Spark Ignition Engine

Combustion and Emission Characteristics of a Spark Ignition Engine Fueled with Ammonia/gasoline and Pure Ammonia

Visualization study on the effects of pre-chamber jet ignition and methane addition on the combustion characteristics of ammonia/air mixtures

Optical diagnostic study on ammonia-diesel and ammonia-PODE dual fuel engines

Combustion Behaviors and Unregular Emission Characteristics in an Ammonia–Diesel Engine

Revealing the NO Formation Kinetics for NH3/CH4 Blends Under Dual-Flame and Premixed Swirl Flame Configurations

Numerical Study on the Ignition and Flame Propagation of Ammonia/ n -Heptane Dual Fuels

Preliminary assessment of the potential for rapid combustion of pure ammonia in engine cylinders using the multiple spark ignition strategy

Numerical investigation of ammonia-rich combustion produces hydrogen to accelerate ammonia combustion in a direct injection SI engine