Abstract:A millimeter-wave (mm-wave) fully integrated pseudo-Doherty load-modulated balanced amplifier (PD-LMBA) with a gain flatness enhancement technique is demonstrated in this article. Unlike the conventional LMBA topology based on using two balanced amplifiers (BAs) in the class-AB/B condition and a control amplifier (CA) in the class-C condition, the CA is used as the main amplifier in the class-B condition and the BAs as the auxiliary amplifiers in the class-C condition in the proposed configuration. Therefore, the proposed architecture only needs to satisfy the load condition at saturation rather than in both saturation and power back-off (PBO) conditions. This design can more easily and flexibly achieve a large dynamic power range. Furthermore, a gain flatness enhancement technique based on a variable cross-coupled pair (VCCP) is proposed to improve AM–AM characteristics without decreasing efficiency. The proposed fully integrated PD-LMBA is fabricated in a commercial 65-nm CMOS process and occupies 1.1 mm $^2$ . Adopting continuous-wave testing, the amplifier is found to provide a peak gain of 25.5 dB with a 3-dB gain bandwidth from 24.3 to 28.2 GHz. At 27 GHz, a measured saturated output power ( $P_{\rm sat}$ ) of 22.2 dBm with a peak power added efficiency (PAE) of 30.4% and output 1-dB compression point power ( $\text{OP}_{1\,\text{dB}}$ ) of 20.1 dBm with 23.6% PAE are achieved. The measured PAE at 8-dB PBO from $P_{\rm sat}$ still reaches 15.0%. Without applying any predistortion technology, the prototype demonstrates an ultralow AM–AM distortion characteristic that is less than 0.6 dB in the linear region at 28 GHz. Modulated signal measurements are also performed at the center frequency of 27 GHz. The amplifier provides 13.2 dBm average output power ( $P_{\rm avg}$ ), 13.8% average PAE, $-26.3$ dBc adjacent channel leakage ratio (ACLR) and $-$ 25.9 dB EVM for a 100 MSym/s single-carrier 64-quadrature amplitude modulation (QAM) signal with a 7.1-dB peak-to-average-power ratio. For a 2.4-Gb/s (400 MSym/s) signal, also at a carrier frequency of 27 GHz, this proposed PD-LMBA still demonstrates 12.3-dBm $P_{\rm avg}$ and 11.9% average PAE with $-$ 25.5 dB rms EVM and $-$ 25.7 dBc ACLR.

C–Ku-Band RF-Input Load Modulated Balanced Amplifier MMIC Utilizing Broadband Saturation Efficiency Enhancement Technique

A 4 W K-Band Gaas Mmic Power Amplifier With 22 Db Gain

Design of X/Ku Dual-Wideband GaN Power Amplifier MMIC Based on Coupled Multiresonator Matching Networks

X-Band High-Efficiency Continuous Class B Power Amplifier Gan Mmic Assisted By Input Second-Harmonic Tuning

Design of a Broadband Ka-band MMIC LNA Using Deep Negative Feedback Loop.

Design and Simulation of a Ku-band MMIC Power Amplifier

Fully integrated pseudo differential K-band power amplifier in 0.13um standard CMOS

A High-Efficiency K-band MMIC Linear Amplifier Using Diode Compensation

A 68.5~90 GHz High-Gain Power Amplifier with Capacitive Stability Enhancement Technique in 0.13 Μm SiGe BiCMOS

A 100–117 GHz W-Band CMOS Power Amplifier With On-Chip Adaptive Biasing

A W-band current combined power amplifier with 14.8dBm Psat and 9.4% maximum PAE in 65nm CMOS

A $ka$ -Band Pseudo-Doherty Load-Modulated Balanced Amplifier with Gain Flatness Enhancement Technique

A Compact E-Band Load-Modulation Balanced Power Amplifier Using Coupled Transmission-Line Output Network Achieving 22.1-Dbm Psat and 34.9%/12.2% Efficiency at Psat/6-dB PBO

Broadband Three-Stage Pseudoload Modulated Balanced Amplifier With Power Back-Off Efficiency Enhancement

A Full Ka-Band Power Amplifier with 32.9% PAE and 15.3-Dbm Power in 65-Nm CMOS

Decade-Bandwidth RF-Input Pseudo-Doherty Load Modulated Balanced Amplifier using Signal-Flow-Based Phase Alignment Design

A Ku-Band Broadband Stacked FET Power Amplifier Using 0.15 μm GaAs pHEMT

A Compact Wideband High-Efficiency Power Amplifier for Ku-Band Applications

AKa-Band Power Amplifier with 22.9 dBm P<inf>sat</inf>, 22.5 dBm OP<inf>1dB</inf> and 21% PAE in 130 nm SiGe BiCMOS

High-efficiency K-band MMIC Power Amplifier Using Multi-Harmonic Load Terminations