Abstract:Photoplethysmography (PPG) is an attractive method to acquire vital signs such as heart rate and blood oxygenation and is frequently used in clinical and at-home settings. Continuous operation of health monitoring devices demands a low power sensor that does not restrict the device battery life. Silicon photodiodes (PD) and LEDs are commonly used as the interface devices in PPG sensors; however, using of flexible organic devices can enhance the sensor conformality and reduce the cost of fabrication. In most PPG sensors, most of system power consumption is concentrated in powering LEDs, traditionally consuming mWs. Using organic devices further increases this power demand since these devices exhibit larger parasitic capacitances and typically need higher drive voltages. This work presents a sensor IC for continuous SpO$_2$ and HR monitoring that features an on-chip reconstruction-free sparse sampling algorithm to reduce the overall system power consumption by $\sim$70\% while maintaining the accuracy of the output information. The designed frontend is compatible with a wide range of devices from silicon PDs to organic PDs with parasitic capacitances up to 10 nF. Implemented in a 40 nm HV CMOS process, the chip occupies 2.43 mm$^2$ and consumes 49.7 $\mu$W and 15.2 $\mu$W of power in continuous and sparse sampling modes respectively. The performance of the sensor IC has been verified \textit{in vivo} with both types of devices and the results are compared against a clinical grade reference. Less than 1 bpm and 1\% mean absolute errors were achieved in both continuous and sparse modes of operation.

A 140-Db Dynamic Range Digital PPG Front-end IC with an Integrated MoSe2 Photodiode for Wearable Non-invasive Pulse Oximetry

A 1.8V 16μA 136.5dB DR PPG/NIRS Recording IC using Noise Shaping Triple Slope Light to Digital Converter

A 119dB Dynamic Range Charge Counting Light-to-Digital Converter For Wearable PPG/NIRS Monitoring Applications

A 196μW, Reconfigurable Light-to-Digital Converter with 119dB Dynamic Range, for Wearable PPG/NIRS Sensors

Novel surgical approaches to fecal incontinence: Neurostimulation and artificial anal sphincter

A 140 Db-Dr Light-to-Digital Converter Using Current-Domain Hybrid Zoom for Baseline Cancellation and Interference Compensation

A 153μw 26nv/√hz Readout Circuit with BW and Power Scalability Using Capacitively-Coupled Chopper Floating Inverter Amplifier Embedded in a Discrete-Time ΔΣ Modulator

A 30- $\mu$ W 94.7-Db SNDR Noise-Shaping Current-Mode Direct-to-Digital Converter Using Triple-Slope Quantizer for PPG/NIRS Readout

A 10.7-Μa 103-Db DR Hybrid Delta-Sigma Modulator for Sensing Applications

A 2.3-5.7μW Tri-Modal Self-Adaptive Photoplethysmography Sensor Interface IC for Heart Rate, SpO2, and Pulse Transit Time Co-Monitoring

A 44μw 140Db-Dr Hybrid Light-to-Digital Converter with Current-Tracking Dynamic Zoom and Power-Scaling OTA

An Integrated High-Gain Wide–Dynamic Range Photoplethysmography Sensor for Cardiac Health Monitoring

A Sparse Sampling Sensor Front-end IC for Low Power Continuous SpO$_2$ \& HR Monitoring

Low-Power High-Sensitivity Photoplethysmography Sensor for Wearable Health Monitoring System

A Low-Power High-Sensitivity Photocurrent Sensory Circuit with Capacitive Feedback Transimpedance for Photoplethysmography Sensing

A 108db DR Hybrid-CTDT Direct-Digitalization ΔΣ-ΣM Front-End with 720mvpp Input Range and >300mv Offset Removal for Wearable Bio-Signal Recording.

A 2.6 μW Monolithic CMOS Photoplethysmographic (PPG) Sensor Operating With 2 μW LED Power for Continuous Health Monitoring

A 107.6 dB-DR Three-Step Incremental ADC for Motion-Tolerate Biopotential Signals Recording

A 48 mW DROIC with 15-bit pixel-level ADC for 640x512 mid-wave infrared imagers

A 48 mW DROIC with 15-bit pixel-level ADC for 640×512 mid-wave infrared imagers

Near‐Infrared Organic Photodetectors toward Skin‐Integrated Photoplethysmography‐Electrocardiography Multimodal Sensing System