Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effect of Chromium and Molybdenum Addition on the Matching Mechanism of Strength−ductility−toughness of Low Carbon Medium Manganese Steel

Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying

Effect of Cr–Mo addition on the microstructure and mechanical properties of medium‐carbon steel

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

Effect of Manganese on the Strength–Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel

Effect of Molybdenum on the Impact Toughness of Heat-Affected Zone in High-Strength Low-Alloy Steel

Effect of Different Water Toughening Treatment on Mechanical Properties and Microstructure of Fe-Mn-C TWIP Steel

Optimizing the Strength and Toughness of V/Mo-Modified 0.22C-5.24Mn Steel by Short-Time Partial Austenitization Process

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Unexpected strengthening of the Mo-containing low-density steel achieved through a novel nano-ordered phase

EFFECT OF MOLYBDENUM ON DELAYED FRACTURE BEHAVIOR OF HIGH STRENGTH STEEL

Tuning mechanical behavior and deformation mechanisms in high-manganese steels via carbon content modification

Refinement mechanism of nanoscale Cu-rich precipitates by Mo addition and its effect on strength-toughness of Cu-bearing low carbon high strength steel

The effect of Ti–Mo–Nb on the microstructures and tensile properties of a Fe–Mn–Al–C austenitic steel

High strength-toughness combination of a low-carbon medium-manganese steel plate with laminated microstructure and retained austenite

Microstructure and High-Temperature Tensile Behavior of Modified H13 Steel with the Addition of Tungsten, Molybdenum, and Lowering of Chromium

Enhancement of Yield Strength by Chromium/Nitrogen Alloying in High-Manganese Cryogenic Steel

Effects of Mn Addition on the Microstructure and Hydrogen Embrittlement Resistance of High Strength Martensitic Steel

Effect of Mo on the high-temperature oxidation behavior of Cr-Ni-Mo Hot-Work Die Steels

Precipitation behavior of Ti–Nb–V–Mo quaternary microalloyed high strength fire-resistant steel and its influence on mechanical properties