Abstract:Spiral scanning mode, where ultrasonic probes relatively rotate forward around a tested bar, is commonly used in an automatic ultrasonic testing system for metal bar quality control. Current non-destructive testing standards for bars with ultrasonic technology specify that whether the bar is rejected or accepted should be made in accordance with the amplitude of the echo from a defect in the bar. The quality information obtained by the abovementioned standard testing procedure is only the echo from the defect, and it is too simple to characterize the defect in detail and accurately. Therefore, inspection using imagery and quantitative nondestructive testing (QNDT) of bar quality is the development trend of bar quality control technology in the future. In achieving QNDT of metal round bars, a synthetic aperture focusing on imaging algorithm in a polar coordinate system (pSAFT) and its surrounding scan-mode time-domain synthetic aperture focusing technology (ST-SAFT) were proposed in accordance with the classical ultrasonic synthetic aperture focusing technology (SAFT) theory on a Cartesian coordinate system. Based on the signal set collected by the spiral scanning automatic detection system, the formula of time-delay superposition imaging expressed by the effective synthetic aperture radian was deduced to image the defects in the bar with a cross-sectional view. By preparing a transverse-hole artificial defect sample for the testing experiment, ultrasonic testing data were processed by ST-SAFT, and then a circular section tomography was imaged. Image edge recognition was used to quantitatively evaluate the sizing ability and positioning resolution of ST-SAFT for defect detection. Experimental results show that the measured value of artificial defects with ST-SAFT is equivalent to the real value; the positioning of the transverse side-drilled hole is accurate, and the imaging resolution is significantly better than that of B-scan. The imaging speed for each circular section can reach the order of milliseconds, which can match the mechanical scanning speed of bar inspection for one circle. Therefore, this technology can be used to improve the technical level of ultrasonic automatic testing equipment for metal round bars and ensure safety of the application of metal round bars.

Synthetic Aperture Imaging Technology for Ultrasonic Spiral Scanning Detection of Metal Bars

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Frequency Domain Synthetic Aperture Focusing Technique for Variable-Diameter Cylindrical Components.

Nondestructive Evaluation of Special Defects Based on Ultrasound Metasurface

Frequency-domain Synthetic Aperture Focusing for Helical Ultrasonic Imaging

Research of Automatic Ultrasonic Test System for Round Bar Flaw

A Model-Based Regularized Inverse Method for Ultrasonic B-scan Image Reconstruction

Synthetic Aperture Imaging for Multilayer Cylindrical Object Using an Exterior Rotating Transducer.

Research of Integrated Ultrasonic Auto Detecting Method on Curved Surfaces

Wavenumber-Domain Fast Reconstruction Technique Using Ultrasonic Scanning for Transverse Wave Imaging

Time-domain Approach for Ultrasonic Non-destructive Detection Based on Synthetic Aperture Focusing Technique

A modified synthetic aperture focusing algorithm used for transmission detection based on laser ultrasonics method

Non-destructive laser-ultrasonic Synthetic Aperture Focusing Technique (SAFT) for 3D visualization of defects

Fast 3-D Ultrasonic Imaging Using Time-Domain Synthetic Aperture Focusing Techniques Based on Circular Scan Conversions

Ultrasonic inspection of curved structures with a hemispherical-omnidirectional ultrasonic probe via linear scan SAFT imaging

Defect imaging based on laser ultrasonic frequency domain synthetic aperture focusing technology with separated generation–detection and 2-D equivalent velocity mapping

Ultrasonic Non-Destructive Testing and Evaluation of Stainless-Steel Resistance Spot Welding Based on Spiral C-Scan Technique

Research on Photoacoustic Synthetic Aperture Focusing Technology Imaging Method of Internal Defects in Cylindrical Components

A High Precision Quality Inspection System for Steel Bars Based on Machine Vision

Multi-mode laser-ultrasound imaging using Time-domain Synthetic Aperture Focusing Technique (T-SAFT)

Fully Noncontact Hybrid NDT for 3D Defect Reconstruction Using SAFT Algorithm and 2D Apodization Window