Abstract:Additive manufacturing (AM) refers to advanced technologies for building 3D objects by adding material layer upon layer using either electron beam melting (EBM) or selective laser melting. AM allows us to produce lighter and more complex parts. However, various defects are created during the AM process, which severely affect fatigue behavior. In the current research, the effects of the anisotropic microstructure in the in-plane and out-of-plane orientations and defects on the fatigue crack propagation rate (FCPR) and crack path were studied. A resonance machine was used to determine the fatigue crack propagation rate (da/dN vs. ΔK) from the near-threshold up to the final fracture, accompanied by in situ Acoustic Emission (AE) monitoring. Micro-Computerized Tomography (μCT) enabled us to characterize surface and microstructural defects. Metallography was used to determine the microstructure vs. orientations and fractography to classify the fatigue fracture propagation modes. Calculations of the local stress distribution were performed to determine the interactions of the cracks with the defects. In the out-of-plane direction, the material exhibited high fatigue fracture toughness accompanied by a slightly lower fatigue crack propagation rate as compared to in-plane orientations. The near-threshold stress intensity factor was slightly higher in the out-of-plane orientation as compared to that in the in-plane one, accompanied by a lower exponent of the Paris law regime. The threshold decreased with an increasing load ratio as expected for both orientations. The crack propagation direction that crosses the elongated grains plays an important role in increasing fatigue resistance in the out-of-plane direction. In the in-plane directions, the crack propagates parallel to the grain boundary, interacts with more defects and exhibits more brittle striations on the fracture surface, resulting in lower fatigue resistance.

Isotropy of Fatigue Crack Growth in Hybrid Additive Manufactured Ti6Al4V ELI Titanium Alloy

Towards Superior Fatigue Crack Growth Resistance of TC4-DT Alloy by In-Situ Rolled Wire-Arc Additive Manufacturing

Fatigue Crack Initiation and Growth Behaviors of Additively Manufactured Ti-6AI-4V Alloy After Hot Isostatic Pressing Post-Process

Microstructural Causes and Mechanisms of Crack Growth Rate Transition and Fluctuation of Additively Manufactured Titanium Alloy

Anisotropy of Fatigue Crack Growth in Wire Arc Additive Manufactured Ti-6Al-4V

Enhanced strength of additively manufactured Ti-6Al-4V alloy through multistage strain hardening

Research on Microstructure and Mechanical Properties of Ti–6Al–4V ELI Fabricated by Hybrid Directed Energy Deposition with In-Situ Rolling and Annealing

Fatigue and anisotropic behavior of wire-arc additive manufactured TC17 titanium alloy

Weakening the Anisotropic Property and Refining Prior-β Grains via Hammer Peening Treatment During Wire Arc Additively Manufacturing of Ti-6Al-4V

Effects of Anisotropic Microstructure and Load Ratio on Fatigue Crack Propagation Rate in Additively Manufactured Ti-6Al-4V Alloy

The Role of Microstructure and Local Crystallographic Orientation Near Porosity Defects on the High Cycle Fatigue Life of an Additive Manufactured Ti-6Al-4V

Additive Manufacturing of Ti-6Al-4V Alloy by Hybrid Plasma-Arc Deposition and Microrolling: Grain Morphology, Microstructure, and Tensile Properties

Tailoring microstructure with special bimodal structure to improve the ductility and fatigue life of laser powder bed fused Ti6Al4V alloy

Effect of energy input on fatigue crack growth behavior of titanium alloy Ti6Al4V made by WAAM‐CMT

Characteristic and mechanism of crack initiation and early growth of an additively manufactured Ti-6Al-4V in very high cycle fatigue regime

Hot Deformation Behavior and Process Optimization of TC4-DT Alloy Fabricated by Wire and Arc Additive Manufacturing with In-Situ Forging

Effect of Microstructure on Fatigue Properties of Several Ti-Alloys for Aerospace Application

Fatigue crack growth behaviour of an Al-Mg4.5Mn alloy fabricated by hybrid in situ rolled wire + arc additive manufacturing

Predicting the Effect of Surface Waviness on Fatigue Life of a Wire + Arc Additive Manufactured Ti-6Al-4V Alloy

Dynamic Mechanical Properties of TC11 Titanium Alloys Fabricated by Wire Arc Additive Manufacturing

In Situ Tailoring Microstructure in Laser Solid Formed Titanium Alloy for Superior Fatigue Crack Growth Resistance