Abstract:Tip clearance flow between rotating blades and the stationary casing in high-pressure turbines is very complex and is one of the most important factors influencing turbine performance. The rotor with a winglet-cavity tip is often used as an effective method to improve the loss resulting from the tip clearance flow. In this study, an aerodynamic geometric optimisation of a winglet-cavity tip was carried out in a linear unshrouded high-pressure axial turbine cascade. For the purpose of shaping the efficient winglet geometry of the rotor tip, a novel parameterisation method has been introduced in the optimisation procedure based on the computational fluid dynamics simulation and analysis. The reliability of a commercial computational fluid dynamics code with different turbulence models was first validated by contrasting with the experimental results, and the numerical total pressure loss and flow angle using the Baseline k-omega Model (BSL κ-ω model) shows a better agreement with the test data. Geometric parameterisation of blade tips along the pressure side and suction side was adopted to optimise the tip clearance flow, and an optimal winglet-cavity tip was proven to achieve lower tip leakage mass flow rate and total pressure loss than the flat tip and cavity tip. Compared to the numerical results of flat tip and cavity tip, the optimised winglet-cavity design, with the winglet along the pressure side and suction side, had lower tip leakage mass flow rate and total pressure loss. It offered a 35.7% reduction in the change ratio [Formula: see text]. In addition, the optimised winglet along pressure side and suction side, respectively, by using the parameterisation method was studied for investigating the individual effect of the pressure-side winglet and suction-side winglet on the tip clearance flow. It was found that the suction-side extension of the optimal winglet resulted in a greater reduction of aerodynamic loss and leakage mass flow than the pressure-side extension of the optimal winglet. Moreover, with the analysis based on the tip flow pattern, the numerical results show that the pressure-side winglet reduced the contraction coefficient, and the suction-side winglet reduced the aerodynamic loss effectively by decreasing the driving pressure difference near the blade tips, the leakage flow velocity, and the interaction between the leakage flow and the main flow. Overall, a better aerodynamic performance can be obtained by adopting the pressure-side and suction-side winglet-cavity simultaneously.

Influence of a Novel Leading-Edge Winglet on the Aerodynamic Characteristics of a Highly Loaded Turbine

A Novel Suction Side Winglet Design Method For High Pressure Turbine Rotor Tips

Aerodynamic Optimisation of a Winglet-Cavity Tip in a High-Pressure Axial Turbine Cascade

A Novel Suction-Side Winglet Design Philosophy for High-Pressure Turbine Rotor Tips

Investigation on the Effects of Winglet Geometry in a High Loading Compressor Rotor

Aerodynamic Optimization of Winglet-Cavity Tip in an Axial High Pressure Turbine Stage

Numerical Investigation of Blade Tip Winglet on Flow Structure in a High Loading Transonic Rotor

High-resolution numerical investigation into the effects of winglet on the aerodynamic performance for a three-dimensional vertical axis wind turbine

Effect of winglets on aerodynamic performance of wind turbine

Experiment Study of Aerodynamic Performance for the Suction-Side and Pressure-Side Winglet-Cavity Tips in a Turbine Blade Cascade

Numerical simulation of the effects of trailing edge thickness on aerodynamic performance of low pressure turbine

The effect of using winglets to enhance the performance of swept blades of a horizontal axis wind turbine

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Improving the Aerodynamic Performance of a High-Loading Turbine Blade by End-Wall Surface Structures

Study the Effect of Winglet Height Length on the Aerodynamic Performance of Horizontal Axis Wind Turbines Using Computational Investigation

Thermal Performance Improvement on Winglet Tip of a Turbine Stage under Engine Condition-Part II: Ejection Angle Adjustment

Comparative analysis of bent and basic winglets on performance improvement of horizontal axis wind turbines

Unsteady Winglet-Cavity Tip on Leakage Flow in a High-Pressure Turbine Stage of Low-Aspect Ratio

Effect of Leading-Edge Optimization on the Loss Characteristics in a Low-Pressure Turbine Linear Cascade

Hybrid RANS/LES Study of Complex Turbulence Characteristics and Flow Mechanisms on the Highly-Loaded Turbine Endwall

Thermal Performance Improvement on Winglet Tip of a Turbine Stage under Engine Condition-Part I: Winglet Geometry Modifications