Abstract:Experimental, numerical and analytical methods were used to investigate the effects of the blade trailing edge thickness on the profile loss of ultrahigh-lift low-pressure turbine blades. Two cascades, the T106C and the T2, were studied. The loss obtained based on the data at the blade trailing edge plane and the plane 0.3 Chord downstream of the trailing edge agree with each other for T106C blade with and without upstream wakes at different Reynolds numbers. The blade profile losses were broken down as the suction surface boundary loss, the pressure side boundary loss and the mixing loss downstream of the trailing edge for six Reynolds numbers. Trailing edge thicknesses varying from 1.4% to 4.7% pitch were investigated at a Reynolds number of 210,000. It was found that the flow distributions across the passage at the trailing edge planes were highly nonuniform. In particular, and as a result, the trailing edge base pressure was higher than the mixed-out static pressure, so the contribution of the base pressure to the mixing loss downstream of the trailing edge plane was to reduce the loss. When the trailing edge thickness increases, there are three main effects: (1) the area with high base pressure region increases, which tends to reduce the downstream mixing loss; (2) the base pressure reduces, which tends to increase the loss; and (3) the flow diffusion downstream of the trailing edge, which tends to increase the loss. The overall result is the combined effect. For the T106C cascade, increasing the trailing edge thickness from 1.9% pitch to 2.8% pitch has a small effect on the loss. Further increasing the trailing edge thickness increases the loss. The T2 blade has a higher lift than the T106C blade, so the effects of the base pressure in reducing the mixing loss downstream of the trailing edge is more evident. The experimental results show that the profile loss first decreases and then increases as the trailing edge thickness increases. CFD, using the transition k-ω SST model and the k-ω SST model, provides good predictions of the aerodynamic performance. It was used to study the cases with trailing edge thicknesses of 1.4% pitch and 2.9% pitch. The profile loss is almost the same for these two trailing edge thickness. The results show that it is possible to use thicker blade trailing edges in low pressure turbines without aerodynamic penalty. This can lead to benefits in terms of mechanical integrity and manufacturing cost reductions.

Numerical simulation of the effects of trailing edge thickness on aerodynamic performance of low pressure turbine

Les and Cdns Investigation of T106c Low Pressure Turbine

The Effects Of Trailing Edge Thickness On The Losses Of Ultra-High Lift Lp Turbine Blades

The Effects of Trailing Edge Thickness on the Losses of Ultrahigh Lift Low Pressure Turbine Blades

Roughness Effects on Flow Losses of a High-Lift Low-Pressure Turbine Cascade

Numerical Simulation for Heat Transfer Properties at Trailing Edge of Gas Turbine Airfoils

Numerical study of flow in low-pressure turbines with undulated suction surface

Numerical Analysis of Leading-Edge Roughness Effects on the Aerodynamic Performance of a Thick Wind Turbine Airfoil

Numerical Study of the Boundary Layer Separation of a Low‐Pressure Turbine Cascade at Different Incidence Angles

Experimental investigations on cooling characteristics of different trailing-edge cutback geometries

Development and application of a profile loss model considering the low-Re effect in low-pressure turbine

Numerical Study on the Influence of Inlet Turbulence Intensity on Turbine Cascades

Investigation of leading-edge protuberances for the performance improvement of thick wind turbine airfoil1

Uncertainty quantification of geometric variations in transonic high-pressure turbine with different trailing edge and throat area distribution

Numerical investigation and loss estimation of high-pressure turbine cascade flow with contoured endwall and incoming wakes

Investigation of aerodynamic loss mechanism on turbine leading edge with slot film cooling based on entropy analysis

Numerical Investigation of Boundary Layer Separation Control on the Low-Pressure Turbine Blade by Oscillatory Blowing

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

Investigation on the effect of hole diameter and wall thickness on the overall cooling effectiveness of turbine vane leading edge

Numerical Analysis on the Influence of the Twisted Blade on the Aerodynamic Performance of Turbine

A total three-dimensional evaluation method to analyze the loss mechanism of film cooling on turbine guide vane