Abstract:In aeroengines, purge flow directly fed from the compressor (which bypasses the combustor) is introduced through the disk space between blade rows to prevent the hot ingress. Higher quantity of purge gas fed through the wheel space can provide additional thermal protection to the passage endwall and blade surfaces. However, the interaction of purge flow with the mainstream flow leads to higher secondary losses. Secondary losses inside a turbine blade passage can be reduced effectively by endwall contouring. This paper presents computational investigation on the influence of non-axisymmetric endwall contouring over endwall secondary flow modification in the presence of purge flow with the pressure side bubble (PSB). The experimental analysis was conducted for the base case without purge and base case with purge (BCP) configurations having flat endwalls. The total pressure loss coefficient and exit yaw angle deviation were measured with the help of a five-hole pressure probe. Static pressure distribution over the blade midspan was obtained by 16 channel Scanivalve. Aerodynamic performances of three different profiled endwalls are numerically analyzed and are compared against the BCP configuration. The effects of different contoured endwall geometries on endwall static pressure distribution and secondary kinetic energy were also discussed. Analysis shows that in the first contoured endwall configuration (EC1), the formation of stagnation zones at a contour valley close to the suction surface causes the exit total pressure loss coefficient to increase. The shifting of the contour valley near to the pressure surface (EC2 configuration) has resulted in local acceleration of the diverted pressure side leg of the horseshoe vortex over the hump toward the end of the passage. In the third configuration (EC3 configuration), reduced valley depth and optimum hump height have effectively redistributed the endwall pitchwise pressure gradient. The increased static pressure coefficient at the endwall near to the pressure surface has eliminated the PSB formation. In addition, computational results of unsteady Reynolds averaged Navier–Stokes simulations are obtained for analyzing transient behavior of PSB, with more emphasis on its migration on the pressure surface and transport across the blade passage. The additional work done by the mainstream fluid to transport the low momentum PSB fluid has caused higher aerodynamic penalty at the blade exit region. In this viewpoint, the implementation of contoured endwalls has shown beneficial effects by eliminating the PSB and related secondary vortices. At 27% of axial chord downstream of the blade trailing edge, a 4.1% reduction in the total pressure loss coefficient was achieved with endwall contouring.

Improving the Aerodynamic Performance of a High-Loading Turbine Blade by End-Wall Surface Structures

Secondary Flow Reduction By Blade Redesign And Endwall Contouring Using An Adjoint Optimization Method

Optimization Design of a Turbine Blade to Reduce Secondary Flow Loss Using a Viscous Adjoint Method

Optimization of Endwall Contours of a Turbine Blade Row Using an Adjoint Method

Turbine Blade Row Optimization Through Endwall Contouring by an Adjoint Method

Hybrid RANS/LES Study of Complex Turbulence Characteristics and Flow Mechanisms on the Highly-Loaded Turbine Endwall

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Aero-Thermal Coupled Design Optimization of the Non-Axisymmetric Endwall for a Gas Turbine Blade

Aerodynamic Loss for a Turbine Blade With Endwall Leakage Features and Contouring

Unsteady Flows of a Highly Loaded Turbine Blade with Flat Endwall and Contoured Endwall

Numerical Investigations on Full Blended Blade and Endwall Technique

Analysis of Flow Structures in a High Pressure Turbine Stator Based on Optimized Endwalls

Numerical Studies On Improving Performance Of Rotor-67 By Blended Blade And Endwall Technique

Investigation on Blended Blade and Endwall Technique

Optimization and Numerical Investigation of Combined Design of Blade and Endwall on Rotor 67

Turbine Blade Endwall Heat Transfer And Film Cooling Performance With Multi-Gap Jets And Film Holes

Improving Turbine Endwall Overall Cooling Effectiveness Using Curtain Cooling and Redistributed Film-Hole Layouts: An Experimental and Computational Study

Multi-Objective Optimization of Non-Axisymmetric Contoured Endwall for Axial Turbines

Aerodynamic performance of profiled endwalls with upstream slot purge flow in a linear turbine cascade having pressure side separation

Experimental investigation on the aerodynamic performance of a transonic turbine rotor with non-axisymmetric endwall

Investigation into the Aerodynamic Performance of a Vertical Axis Wind Turbine with Endplate Design