Abstract:Formation of uniform pileup morphology and excellent bonding strength between two adjacent metal droplets are essential in droplet-based 3D printing. However, due to the unstable included angle ("gap") of the pileup droplets generated by the complex coupling effect between the fluid flow and thermal deformation during the printing process, the successive pileup droplets tend to form poor accuracy morphologies, non-uniform properties, and low-quality bonding strength of the formed microstructure. Since the unstable flow and thermal deformation of the liquid metal is inherent properties in droplet-based 3D printing technique with the same parameter conditions, the morphological deterioration or even instability pileup process still remain common challenge in this technique. Here, the effects of velocity and thermal behaviors on the morphology and size of the pileup droplets were revealed. To accomplish this, a droplet pileup numerical model based on the volume of fluid (VOF) was developed to analyze the spreading and solidification mechanism of the pileup process. In addition, a series of printing experiments with the successive pileup of Sn droplets, generated by a self-developed piezo-electric micro-jet device (PMJD), were conducted to demonstrate the effects of impacting velocity and solidified temperature on the pileup morphology. The evolution mechanisms of impacting velocity and heat accumulation effect and its influence on the dimensional accuracy were revealed. Finally, the originality of this work is an ultrasonic-assisted metal droplet pileup (UAMDP) method was first proposed and applied to effectively regulate the pileup morphology and improve the bonding strength. The evolutions of the influence of the velocity field, temperature field, and pileup behaviors during the spreading process were analyzed thoroughly. A surface morphology analysis further showed the effect of ultrasonic vibration on the contact region between two pileup droplets. And experiments showed that such UAMDP (under voltage of VP-P = 15 V) has 5.9 times enhancement in the adhesion tangential force between two pileup metal droplets. This study provides a foundation for further development of metal droplet-based 3D printing technology.

Formation Mechanism and Elimination Method of Joint Defects in Lattice Structures Printed by Metal Droplet Deposition Manufacturing

Heat Input Adjustment Process for Unsupported Aluminum Alloy Lattice Struts Continuous Forming by Wire Arc-Directed Energy Deposition

Support Equilibrium Design for Laser Additive Manufacturing of Lightweight Component Based on Geometric Deformation Minimization

A Novel Method for Additive Manufacturing Zero Thermal Expansion Lattice Structures Based on Uniform Metal Droplet 3D Printing

Experimental Investigation and Numerical Modeling of Laser Powder Bed Fusion Process-Induced Angle-Dependent Defects in Strut-Based Lattice Structure

Hierarchical design and coupling deformation of lattice structures with variable unit cells manufactured by laser powder bed fusion

A new strategy for eliminating bottom hole defects during aluminum droplet printing within a broad temperature range

Formation mechanisms and control strategies of metallurgical defects and microstructures during laser powder bed fusion of AlSi10Mg lattice structures

Geometric deviation and compensation for thin-walled shell lattice structures fabricated by high precision laser powder bed fusion

Flow and Thermal Coupling Analysis in Metal Droplet-Based 3D Printing: Evolution Mechanism and Regulation Strategy under Ultrasonic Vibration

Suppression of the height deviation on metal bumps manufacturing by an ultrasonic vibration control

Effect of geometric defects on the mechanical properties of additive manufactured Ti6Al4V lattice structures

Micro and Nanolattice Fabrication Using Projection Micro Litho Stereo Exposure Additive Manufacturing Techniques and Synchrotron X-ray 3D Imaging-Based Defect Characterization

Residual Deformation Analysis of Laser Powder Bed Fusion-Fabricated Lattice Structures

Hole-defects in Soluble Core Assisted Aluminum Droplet Printing: Metallurgical Mechanisms and Elimination Methods

Process-induced Geometric Defect Sensitivity of Ti–6Al–4V Lattice Structures with Different Mesoscopic Topologies Fabricated by Electron Beam Melting

Embedded Printing Trace Planning for Aluminum Droplets Depositing on Dissolvable Supports with Varying Section

Deformation Behavior of Heterogeneous Multi-Morphology Lattice Core Hybrid Structures

Formation Of Uniform Metal Traces Using Alternate Droplet Printing

Generation mechanism and suppression method of landing error of two successively deposited metal droplets caused by coalescence and solidification

Precise Control of Variable-Height Laser Metal Deposition Using a Height Memory Strategy