Abstract:Highly efficient and stable, rigid and flexible p‐i‐n perovskite solar cells are developed by incorporating a 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride additive into the lead iodide precursor solution to prepare a porous PbI2 layer. The good diffusion of the organic ammonium salt results in flat and dense perovskite film with large particle size, which achieves high power conversion efficienciesPCE of 23.40% (rigid) and 21.10% (flexible) with excellent ambient and mechanical stability. Flexible perovskite solar cells (FPSCs) are attracting widespread research and attention for their benefits as the next‐generation wearable electronic products. However, there are still many challenges in the quest to achieve dense, pinhole‐free, high crystal quality, low defect, and stable perovskite films, which limit further improvement in the efficiency and stability of FPSCs. Herein, a novel technique for the incorporation of quaternary ammonium halide (QAH) additives to prepare fluffy porous lead iodide layers by using a two‐step sequential deposition method, is reported. Benefiting from the good diffusion of organic amine salts on porous PbI2 layers, flat and dense perovskite films are produced with large particle sizes, few defects, and high crystal quality. Finally, the champion rigid and flexible p‐i‐n PSCs with the 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride (AtaCl) additive achieves exciting power conversion efficiencies (PCE) of 23.40% and 21.10%, respectively. The device with the AtaCl additive retains over 90% of its original PCE under ambient conditions (40 ± 5% relative humidity (RH)) over 1000 h of aging without encapsulation. In addition, the flexible device with the AtaCl additive shows excellent stability under mechanical bending conditions, retaining ≈85% of its original PCE after 10 000 cycles (bending radius = 5 mm).

One-Stone-for-Two-Birds Method to Improve the SnO<sub>2</sub> Layers for High Power-per-Weight Flexible Perovskite Solar Cell Mini-modules

One-Stone-for-Two-Birds Method to Improve the SnO 2 Layers for High Power-per-Weight Flexible Perovskite Solar Cell Mini-modules

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

High‐Performance Flexible Perovskite Solar Cells via Precise Control of Electron Transport Layer

SnO2 Surface Modification and Perovskite Buried Interface Passivation by 2,5‐Furandicarboxylic Acid for Flexible Perovskite Solar Cells

Efficient flexible perovskite solar cells and modules using a stable SnO2-nanocrystal isopropanol dispersion

Ameliorating the Interfacial Mismatch of SnO2 and Perovskite Enabling High Mechanical Stability for Flexible Perovskite Solar Cells

Buried Interface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Mechanical Stability

Large improvement of photovoltaic performance of flexible perovskite solar cells using a multifunctional phospho-ethanolamine-modified SnO2 layer

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Active SnO2 Crystal Planes Enable Efficient and Ultra‐Bendable n‐i‐p Perovskite Solar Cells with Record Certificated Power Conversion Efficiency

Porous Lead Iodide Layer Promotes Organic Amine Salt Diffusion to Achieve High Performance p‐i‐n Flexible Perovskite Solar Cells

Creating a Dual‐Functional 2D Perovskite Layer at the Interface to Enhance the Performance of Flexible Perovskite Solar Cells

Multifunctional Polymer‐Regulated SnO 2 Nanocrystals Enhance Interface Contact for Efficient and Stable Planar Perovskite Solar Cells

High-Performance Electron Transport Layer via Ultrasonic Spray Deposition for Commercialized Perovskite Solar Cells

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Fully printed flexible perovskite solar modules with improved energy alignment by tin oxide surface modification

Highest‐Efficiency Flexible Perovskite Solar Module by Interface Engineering for Efficient Charge‐Transfer

Enhancing Electron Transport Via Graphene Quantum Dot/sno2 Composites for Efficient and Durable Flexible Perovskite Photovoltaics

Outstanding Performance Of Electron-Transport-Layer-Free Perovskite Solar Cells Using A Novel Small-Molecule Interlayer Modified Fto Substrate