Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Performance Improvement of AgBiI4 Solar Cells by a Lewis Base Thiourea Additive

Thiourea with sulfur-donor as an effective additive for enhanced performance of lead-free double perovskite photovoltaic cells

Photovoltage Approaching 0.9 V for Planar Heterojunction Silver Bismuth Iodide Solar Cells with Li-TFSI Additive

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

25.71%-Efficiency FACsPbI3 Perovskite Solar Cells Enabled by A Thiourea-based Isomer

Silver Bismuth Sulfoiodide Solar Cells: Tuning Optoelectronic Properties by Sulfide Modification for Enhanced Photovoltaic Performance

Bismuth Complex Controlled Morphology Evolution and CuSCN-Induced Transport Improvement Enable Efficient BiI3 Solar Cells

First Investigation of Additive Engineering for Highly Efficient Cs2AgBiBr6-based Lead-Free Inorganic Perovskite Solar Cells

Tuning the Bandgap in Silver Bismuth Iodide Materials by Partly Substituting Bismuth with Antimony for Improved Solar Cell Performance

Enhanced Stability of Ag2BiI5 Perovskite Solar Cells by Adding Pyridine Derivatives in Hole‐Transporting Materials

Guanidinium Thiocyanate Additive Engineering for High-Performance CsPbIBr 2 Solar Cells with an Efficiency of 10.90%

Adjustable Skeleton of Bilateral Lewis Base Passivator for CsPbI 3 Perovskite Solar Cells with PCE over 20% and Superior Stability

Antimony Doping of CsBi 3 I 10 for Tailoring the Film Morphology and Defects toward Efficient Lead-Free Thin-Film Solar Cells

Enhanced performance of CsPbI2Br perovskite solar cell through improving the solubility of the components in precursor

Solution-Processed Air-Stable Copper Bismuth Iodide for Photovoltaics

Modulating Interfacial Carrier Dynamics via Spatial Conformation toward Efficient and Stable Perovskite Solar Cells

Improving the Performance of Polymer Solar Cells with Benzo[ghi]perylenetriimide-Based Small-Molecules as Interfacial Layers

Improved performance of polymer solar cells by doping with Bi2O2S nanocrystals

Construction of Efficient Cs2AgBiBr6 Perovskite Solar Cells by Enhancing Hole‐Selective Contact with Deep‐Level Dopant‐Free Hole Transport Material

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Passivating A-Site and X-Site Vacancies Simultaneously Via N-Heterocyclic Amines for Efficient Cs2AgBiBr6 Solar Cells.