Abstract:It is a great challenge to detect in-situ high-frequency vibration signals for extreme environment applications. A highly sensitive and robust vibration sensor is desired. Among the many piezoelectric materials, single-crystal lithium niobate (LiNbO3) could be a good candidate to meet the demand. In this work, a novel type of micro-electro-mechanical system (MEMS) vibration sensor based on a single crystalline LiNbO3 thin film is demonstrated. Firstly, the four-cantilever-beam MEMS vibration sensor was designed and optimized with the parametric method. The structural dependence on the intrinsic frequency and maximum stress was obtained. Then, the vibration sensor was fabricated using standard MEMS processes. The practical intrinsic frequency of the as-presented vibration sensor was 5.175 kHz, which was close to the calculated and simulated frequency. The dynamic performance of the vibration sensor was tested on a vibration platform after the packaging of the printed circuit board. The effect of acceleration was investigated, and it was observed that the output charge was proportional to the amplitude of the acceleration. As the loading acceleration amplitude is 10 g and the frequency is in the range of 20 to 2400 Hz, the output charge amplitude basically remains stable for the frequency range from 100 Hz to 1400 Hz, but there is a dramatic decrease around 1400 to 2200 Hz, and then it increases significantly. This should be attributed to the significant variation of the damping coefficient near 1800 Hz. Meanwhile, the effect of the temperature on the output was studied. The results show the nearly linear dependence of the output charge on the temperature. The presented MEMS vibration sensors were endowed with a high output performance, linear dependence and stable sensitivity, and could find potential applications for the detection of wide-band high-frequency vibration.

Imaging Resonant MEMS with Ultra-Broad Spectral Vibrometry from 1000 Hz to 10 GHz

Thin‐Film‐Lithium‐Niobate Photonic Chip for Ultra‐Wideband and High‐Precision Microwave Frequency Measurement

Dynamic imaging of micro-vibrations with an ultra-wide bandwidth and a femtometer noise using switchable pulsed laser interferometry

IMAGING GIGAHERTZ DYNAMICS IN MICROMECHANICAL RESONATORS USING ULTRAFAST PULSED LASER INTERFEROMETRY

Femtometer-amplitude imaging of coherent super high frequency vibrations in micromechanical resonators

Nanoscale imaging of super-high-frequency microelectromechanical resonators with femtometer sensitivity

Single-particle vibrational spectroscopy using optical microresonators

Phase Sensitive Imaging of 10 GHz Vibrations in an AlN Microdisk Resonator

Single-particle Photoacoustic Vibrational Spectroscopy Using Optical Microresonators

A Wide Bandwidth Real-Time MEMS Optical Power Meter with High Resolution and Linearity

Self-Aligning Optical MEMS Acoustic Sensors With nPa/√Hz Resolution

High-sensitivity monitoring of micromechanical vibration using optical whispering gallery mode resonators

A mach-zehnder photonic mems microphone with high sensitivity, 1/f noise suppression, and broadband response

Mirrorless MEMS imaging: a nonlinear vibrational approach utilizing aerosol-jetted PZT-actuated fiber MEMS scanner for microscale illumination

800× Non-Distortion Magnified Visualization of Deep Sub-Nanometer MEMS Vibrations Using a Camera

Active Frequency Tuning for Magnetically Actuated and Piezoresistively Sensed MEMS Resonators

High-Performance Piezoelectric-Type MEMS Vibration Sensor Based on LiNbO3 Single-Crystal Cantilever Beams

High-Precision Ultra-Long Air Slit Fabrication Based on MEMS Technology for Imaging Spectrometers

The Recent Progress of MEMS/NEMS Resonators

Optomechanical Frequency Comb Based on Multiple Nonlinear Dynamics

Optical Fourier Transform Based In-Plane Vibration Characterization for MEMS Comb Structure