Abstract:To increase power density of polymer electrolyte membrane fuel cells (PEMFCs), further optimization and downsizing of cell and stack design are necessary. To support cell and stack design, we have been developing a three-dimensional (3D) PEMFC simulator P-Stack [1]. P-Stack can estimate power generation performance in good agreement with experimental results, and can clarify relationships between the performance and internal states depending on cell designs, operation conditions, and material properties [1]. Although 3D PEMFC simulations are powerful means, preparing 3D model is very time consuming, thus it was difficult to explore various cell designs. In the present study, we have developed a new modeling technology for PEMFC flow fields. In this technology (Figure (a)), flow fields of anode and cathode gases are drawn by lines in 2D canvas. Properties of the lines such as width, depth and wall angle are given, then it automatically generate 3D model for anode/cathode flow fields and bipolar plates, coolant flow field, seal, gasket and MEA. Power generation performance of the 3D model can be estimated by P-Stack continuously. In addition, the line properties, vertex positions, and the number of repeat can be parametrized, enabling the parametric study of cell design. In this technology, pressure and flow rate distributions can be calculated by a network model based on Darcy's law [1], without generating 3D model. As shown in Figure (b), the result is in good agreement with computational fluid dynamics (CFD) calculation of 3D model. Although the CFD calculation takes several hours using 32 parallel processes, the calculation of the network model is finished within several seconds using single process. In similar manner, it can calculate flow rate distribution of cells in the stacking axis. Since the execution time per one case is very short, it can be combined with optimization by genetic algorithm (GA). In the presentation, we will talk about a result of the parametric study and optimization for more practical cell design. Influence of flow field design on power generation performance and internal states will be discussed. References [1] T. Tsukamoto, T. Aoki, H. Kanesaka, T. Taniguchi, T. Takayama, H. Motegi, R. Takayama, S. Tanaka, K. Komiyama, M. Yoneda, J. Power Sources 488 (2021) 229412 Figure 1

A Comprehensive 3D Modelling Exploration of a Protonic Ceramic Electrolysis Cell Stack with Metal Foam

A Deep-Learning-boosted Surrogate Model of a Metal Foam Based Protonic Ceramic Electrolysis Cell Stack for Uncertainty Quantification

Towards Feasible Temperature Management and Thermo-Mechanical Stability of Carbon-Assisted Solid Oxide Electrolysis Cell

Development of Integrated Packaged Single Fuel Cell Short Stack Based on Titanium Metal Plates for Mobile Power Generation

Water management and performance enhancement in proton exchange membrane fuel cell through metal foam flow field with hierarchical pore structure

Design and Modelling of 3D Bionic Cathode Flow Field for Proton Exchange Membrane Fuel Cell

High Power Density & Energy Density Li-ion Battery with Aluminum Foam Enhanced Electrode: Fabrication and Simulation

Experimental performance investigation on the arrangement of metal foam as flow distributors in proton exchange membrane fuel cell

Developing Next Generation High Performance Polymer Electrolyte Membrane Fuel Cells Using Metal Foam As Gas Diffusion Layer

Three-dimensional Performance Simulation of PEMFC of Metal Foam Flow Plate Reconstructed with Improved Full Morphology

Effects of gradient porosity in the metal foam flow field on the performance of a proton exchange membrane fuel cell

Thermal management improvement of air-cooled proton exchange membrane fuel cell by using metal foam flow field

A Metallic Gas Diffusion Layer and Porous Media Flow Field for Proton Exchange Membrane Fuel Cells

Revealing interactions between the operating parameters of protonic ceramic electrolysis cell: A modelling study

Multi-objective Optimization of Protonic Ceramic Electrolysis Cells Based on a Deep Neural Network Surrogate Model

Water management and structure optimization study of nickel metal foam as flow distributors in proton exchange membrane fuel cell

An Innovative Approach to Design and Optimize Flow Field Pattern of Polymer Electrolyte Membrane Fuel Cell

Investigation of metal foam porosity and wettability on fuel cell water management by Electrochemical Impedance Spectroscopy

Metal-foam-based cathode flow-field design to improve H2O retention capability of passive air cooled polymer electrolyte fuel cells

(Invited) Proton‐Conducting Solid Oxide Electrolysis Cells for Hydrogen Production - Materials Design and Catalyst Surface Engineering

Full-scale three-dimensional simulation of air cooling metal bipolar plate proton exchange membrane fuel cell stack considering a non-isothermal multiphase model