Abstract:Film cooling is widely used in modern gas turbines for the protection of the hot components against hot gases from the combustion process. Film cooling directly influences the thermal efficiency of the gas turbine, as the cooling gas is extracted from the compressor and mixed with the mainstream in the hot component. Huge efforts by industry as well as research organizations have been undertaken to improve the film cooling effectiveness. It can been concluded that there are two key points for the improvement of film cooling effectiveness, constraining the blow-off of cooling ejection and extending the lateral coverage of cooling gas. The paper presents a new cooling technology, which reaches high film-cooling effectiveness as a result of a well-designed cooling hole, named SYCEE film cooling technology (SFCT). Plate film cooling experiments of SYCEE tested by pressure sensitive paint (PSP) are carried out in this work, and traditional shape-hole are included as well for baselines. It is resulted that SFCT has a better film cooling performance than shape-hole in the same conditions, and the gap of the averaged film cooling effectiveness between them continuously enlarges as the blowing ratio increases. Furthermore, an application of SFCT on the first stage vane of an F-class gas turbine is studied as well. A two-dimension cascade has been employed to measure the cooling performance of SFCT using pressure sensitive paint (PSP) as well, and the tested vanes separately with round-hole and shape-hole are considered again for baselines. The different kinds of film holes separately locate on the pressure and suction side, while the showerhead in different cases are kept the same, arranged with round-holes. The cooling air is ejected at inclination angle 45° with compound-angle 90° in the showerhead and inclination angle 35°∼45° without compound-angle on the pressure side and suction side. The detailed local cooling effectiveness distributions as well as the span-averaged effectiveness over the vane surface are presented. As expected, the film cooling performance of round-hole is the worst due to the lift-off of the cooling ejection. SFCT has better film cooling performance than shape-hole on the pressure side, but the advantage decreases along the mainstream direction. However, the span-averaged film cooling effectiveness of SYCEE is similar with that of the shape-hole on the suction side. This may be due to enhanced impact of mainstream flow derived from the pressure gradient in the turbine passage, and consequently weakening the effect of film hole on the suction side.

Investigation of Modified Sweeping Jet Film Cooling on Turbine Vane

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Study on Effects of Modern Turbine Blade Coolant Injecting Nozzle Position on Film Cooling and Vortex Composite Performance under Rotating Conditions

Improved Turbine Vane Endwall Film Cooling by Using Sand-Dune-Inspired Design

A TEMPERATURE-GRADIENT CORRECTION METHOD FOR FILM COOLING EFFECTIVENESS MEASUREMENT USING ENDOSCOPE-BASED PSP TECHNIQUE

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

Experimental Investigation of Film Cooling of the Leading Edge and Pressure Side of a Turbine Vane

Experimental investigation on the combined cooling methods of jet impingement and film cooling for the pressure surface of the turbine vane leading cavity

Experimental and unsteady numerical investigations on cooling characteristics of trailing-edge cutback with effect of upstream film holes

Experimental and numerical investigations on film cooling characteristics and hole shape improvement of turbine vane at one engine inoperative condition

Novel Shaped Sweeping Jet for Improved Film Cooling and Anti-Deposition Performance

Study of film cooling on a turbine guide vane pressure side with a serrated trench

Experimental investigation of hole-geometry effect on unsteady characteristics of film cooling at turbine vane leading edge

Experimental Investigation of Wall Thickness and Hole Shape Variation Effects on Full-Coverage Film Cooling Performance for a Gas Turbine Vane

Experimental Investigations of SYCEE Film Cooling Performance on a Plate and a Tested Vane of an F-Class Gas Turbine

Large eddy simulations of the turbine vane pressure side film cooling flows of cylindrical and fan-shaped holes with a saw-tooth plasma actuator

Experimental and numerical investigation on the film-cooling on a gas turbine vane pressure side with various internal rib angles

Conjugate Heat Transfer Investigation on Swirl-Film Cooling at the Leading Edge of a Gas Turbine Vane

Film Cooling Effectiveness on Pressure Surface and Suction Surface of Turbine Guide Vane with Diffusion Slot Holes

Experimental and numerical investigations of vane endwall film cooling with different density ratios

Heat transfer and flow structure characteristics of film-cooled leading edge model with sweeping and normal jets