Abstract:For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in the presence of rubber particles because the Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that on the hydrated cement particles. Thus, the compressive strength of Rubcrete could be improved by increasing the Hamaker constant of the system. This was achieved by increasing the refractive indices of the solids (n(s)). The refractive indices of materials increase with increases in functional groups, such as OH and SH on the surface. The model provided a possible mechanism for the efficacy of treating rubber particles with NaOH in improving the compressive strength. By using NaOH solution treatment, an oxygen-containing OH group was formed on the rubber surface to increase the Hamaker constant of the system, leading to higher compressive strength. Based on this mechanism, a novel method for modification of the rubber particles was also proposed. In this process, the rubber particles were partially oxidized with hot air/steam in a fluidized bed reactor to produce the hydrophilic groups on the surface of the particles. Preliminary results obtained so far are promising in accordance with the theory.

Enhancing Interface Adhesion Between Waterjet‐produced Rubber Powders and Natural Rubber by Wet‐mixing Method

High-value recycling of waste tire rubber powder by wet mixing method

Effect of low-cost mussel-inspired poly(catechol/polyamine) modification of waste brick powder followed by grafting of epoxy elastomers on natural rubber composites

Preparation of High-Performance Composite Hydrogel Reinforced by Hydrophilic Modified Waste Rubber Powder

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Improving Dispersion of Carbon Nanotubes in Natural Rubber by Using Waterjet-Produced Rubber Powder as a Carrier

Research Progress of Natural Rubber Wet Mixing Technology

Study of the Effect of Surface-Modified Rubber Particles on the Properties of UHPC Containing Polyoxymethylene Fibers

Effects of waste rubber particles on workability, mechanical, and sound insulation properties of recycled aggregate mortar

Mechanism on surface hydrophobically modification of fibrous wollastonite and its reinforcement of natural rubber

Enhancing Natural Rubber Tearing Strength by Mixing Ultra-High Molecular Weight Polyethylene Short Fibers

Preparation and performance of natural rubber latex treatment for silica filled natural rubber composites

The structure and properties of mechanochemically modified acrylonitrile butadiene rubber (NBR)/poly (vinyl chloride) (PVC) scraps and fresh NBR composites

Microwave Irradiated Polyester Staple Fibers for Natural Rubber with Excellent Interface Performance

Mechano-chemical rubber reclamation using aminolysis products of waste flexible polyurethane foams as the devulcanizing agent

Modified Waste Rubber Powders Filled Styrene Butadiene Rubber Toward the Combination of High Elasticity and Low Mechanical Hysteresis

Use of waste rubber as concrete additive

High performance, self-adhesive and recyclable dynamic crosslinked waste rubber particle blends toward upcycling of waste rubber

Synergistic Development of Natural Rubber/Butyl Rubber Composites for Improved Interfacial Bonding and Enhanced Shock-Absorbing Capabilities

Reinforcing and plasticizing effects of reclaimed rubber on the vulcanization and properties of natural rubber

Preparation of high-quality wollastonite/natural rubber composites by atomization sputtering rapid drying process