Abstract:Although fly ash foam concrete (FAFC) is lightweight, heat-retaining, and insulating, its application options are constrained by its weak construction and short lifespan. The effects of various dosage ratios of the foaming agent (i.e., hydrogen peroxide), silica fume, and polypropylene fiber on the dry density, compressive strength, thermal insulation performance, pore structure parameters, and durability of FAFC were analyzed in this study, which sought to address the issues of low strength and low durability of FAFC. According to the findings, there is a negative correlation between the amount of hydrogen peroxide (as the foaming agent) and compressive strength, and, as the silica fume and polypropylene fiber (PP fiber) content rise, the strength will initially rise and then fall. The distribution of pore sizes gradually shifts from being dominated by small pores to large pores as the amount of foaming agent increases, while the porosity and average pore size gradually decrease. When the hydrogen peroxide content is 5%, the pore shape factor is at its lowest. The pore size distribution was first dominated by a small pore size and thereafter by a large pore size when the silica fume and PP fiber concentration increased. Prior to increasing, the porosity, average pore size, and pore shape factor all decreased. Additionally, the impact of PP fiber on the freeze–thaw damage to FAFC was also investigated at the same time. The findings indicate that the freeze–thaw failure of FAFC is essentially frost heave failure of the pore wall. The use of PP fiber is crucial for enhancing FAFC's ability to withstand frost. The best frost resistance is achieved at 0.4% PP fiber content. In conclusion, the ideal ratio for overall performance was found to be 5% hydrogen peroxide content, 4% silica fume content, and 0.1% polypropylene fiber content. The results obtained could be applied in different fields, such as construction and sustainable materials, among others.

Study of the Control and Influence of Humidity on the Mechanical and Structural Properties of Geopolymer Foam Composites Based on Fly Ash and Wood Flour

STUDY ON THE INFLUNCE OF CELLULOSE ETHERS ON FLY ASH MORTAR

Investigation on the Effect of Fiber Wettability on Water Absorption Kinetics of Geopolymer Composites

Effect of Waste Glass Powder and Bamboo Fiber on the Physico-Mechanical Properties and High-Temperature Behavior of a Fly Ash-Based Geopolymer

Physical and mechanical properties and micro characteristics of fly ash-based geopolymer paste incorporated with waste Granulated Blast Furnace Slag (GBFS) and functionalized Multi-Walled Carbon Nanotubes (MWCNTs)

Compressive Strength and Thermal Conductivity of Fly Ash Geopolymer Concrete Incorporated with Lightweight Aggregate, Expanded Clay Aggregate and Foaming Agent

Microstructure, Compressive Strength and Sound Insulation Property of Fly Ash-Based Geopolymeric Foams with Silica Fume as Foaming Agent

Study on Improving Measures of Mechanical Properties of Geopolymer Materials and Its Effect on CO2 Emission

Residual water and interfacial bonding effects on the mechanical performance of CNT/fly ash geopolymer binder

An efficient approach for sustainable fly ash geopolymer by coupled activation of wet-milling mechanical force and calcium hydroxide

Experimental study on full-volume fly ash geopolymer mortars: Sintered fly ash versus sand as fine aggregates

Investigating the Mechanical and Durability Characteristics of Fly Ash Foam Concrete

Investigation on Physical Behavior, Impermeability and Micromechanism of Engineering Geopolymer Composites Modified with MWCNTs

Influence of Waste Glass Particle Size on the Physico-Mechanical Properties and Porosity of Foamed Geopolymer Composites Based on Coal Fly Ash

Effect of fly ash cenospheres on properties of multi-walled carbon nanotubes and polyvinyl alcohol fibers reinforced geopolymer composites

Synthesis of metakaolin-based geopolymer foamed materials using municipal solid waste incineration fly ash as a foaming agent

Synthesis and Characterization of Red Mud and Rice Husk Ash-Based Geopolymer Composites

WFT-based assessment of the rheological characteristics, particle packing, and buildability of Pcc-FA-GGBFS composite materials for 3D printing

Surface modification and dispersity of chopped carbon fiber and its effects on mechanical properties of gypsum-based composite materials

Mechanical Properties and Coagulation Characteristics of Flue Gas Desulfurization Gypsum-Based Polymer Materials

Study on the Reinforced Properties of Geopolymer Fibers with a Sustainable Development Role