Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Research on Load Adaptability Expansion of Zero-Dimensional Heat Release Prediction for Direct-Injection Diesel Engines

Improved Thermodynamic Model for Lean Natural Gas Spark Ignition in a Diesel Engine Using a Triple Wiebe Function

Multidimensional Computational Fluid Dynamics Combustion Process Modeling of a 6V150 Diesel Engine

Twin-Peak Heat Release Phenomenon Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

A Study on Performance Prediction of D.I.Diesel Engine from Fuel Injection Rate

Combustion model development of future DI engines for carbon emission reduction

Research on Load Prediction of Low-Calorific Fuel Fired Gas Turbine Based on Data and Knowledge Hybrid Model

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Experimental Investigation and Numerical Modeling of Spray Combustion and Emission in a Diesel Engine

Investigation of the Effect of Simulated Atmospheric Conditions at Different Altitudes on the Combustion Process in a Heavy-Duty Diesel Engine Based on Zero-Dimensional Modeling

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

Study of In-Cylinder Heat Transfer Boundary Conditions for Diesel Engines under Variable Altitudes Based on the CHT Model

Data-Driven Prediction of Key Combustion Parameters Based on an Intelligent Diesel Fuel Injector for Large Engine Applications

The Engine Combustion Phasing Prediction Based on the Support Vector Regression Method

Development and Validation of a Modeling and Calibration Method for Diesel-Like Multistage Combustion Based On a Modified Multi-Wiebe Function

An Advanced High Dimensional Model Representation Approach for Internal Combustion Engine Modeling and Optimization

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Computational Modeling and Analysis of Diesel-fuel Injection and Autoignition at Transcritical Conditions

Diesel Engine Emissions Simulation and Test in Working Process

A semi-empirical model for online real-time control of NOX generation in diesel engines