Abstract:In situ compressive behavior of carbon fibers reinforced PPS laminates. This study investigates the influence of a combined thermal heat flux (imposed by a cone calorimeter) and a compressive loading on the deformation and damage mechanisms within quasi‐isotropic carbon fibers reinforced thermoplastic (polyetherether ketone [PEEK] and polyphenylene sulfide [PPS]) and thermosetting (epoxy) laminates. First, thermogravimetric Analyses conducted under nitrogen provide valuable information on the thermal decomposition of these materials depending on the matrix nature (580–510°C and 350°C, respectively) which is a key factor to explain the mechanical behavior under fire conditions. Second, under the same testing conditions (creep loading under a 50 kW/m2 heat flux), the time to failure is about 17 times as high (C/PEEK), twice as high (C/PPS) with respect to C/epoxy laminates. At the ply scale, the exposure of thermoplastic matrices (PEEK and PPS) to a 50 kW/m2 heat flux causes softening and thermal decomposition, facilitating the micro‐buckling of fiber bundles in matrix‐rich areas. At the laminates scale, this mechanism ultimately leads to the formation and propagation of plastic kink bands in the transverse direction. In epoxy‐based laminates, the onset of matrix pyrolysis occurs at lower temperatures (350°C) during thermal aggression, and thermal decomposition has started in all the plies of the laminates. Combined with the low ductility of the epoxy matrix, the compressive response is elastic‐brittle and results from the buckling of 0° plies outside the thermally‐damaged area. Highlights Study on the compression of polymer composites exposed to a 50 kW/m2 heat flux. The influence of the matrix nature (thermoplastic vs thermoset) is discussed. Time to failure is about 17 times higher in C/PEEK compared to C/Epoxy. Plastic kink bands propagate in thermoplastic composites at T > Tg. C/Epoxy laminates undergo buckling outside the thermally damaged area.

Temperature Field Characteristics of CF/PEEK Thermoplastic Composites Formed by Automated Fiber Placement Using Hot Gas Torch with Slit Structure Nozzle

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

The effect of temperature field on the characteristics of carbon fiber reinforced thermoplastic composites in the laying and shaping process

Thermal Management for Thermoset Automated Fiber Placement Based on Infrared Heater Structure Arrangement

As-built FE Thermal Analysis for Complex Curved Structures in Automated Fiber Placement

Temperature Field in the Heat Transfer Process of PEEK Thermoplastic Composite Fiber Placement

Modeling for Heat Transfer of the Thermoplastic Composites <I>In Situ</I> Automated Fiber Placement Process

Laser-assisted AFP-TPC Manufacturing of CF/PEEK High-Performance Thermoplastic Composites with Low Warpage-Deformation Defects

Modeling and Analysis of Heat Transfer in Fiber Placement Process of Thermoplastic Composites

Hot gas temperature effect on thermoplastic composites thermal using the automated tape laying

High performance thermoplastic polymer for the compressive behaviour of carbon fibre reinforced composites

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Optimization of Thermoplastic Composites Process Parameters Based on Robotic Fiber Placement

Atomistic Modeling of the Effect of Temperature on Interfacial Properties of 3D-Printed Continuous Carbon Fiber-Reinforced Polyamide 6 Composite: From Processing to Loading

Process parameter–mechanical property relationships and influence mechanism of advanced CFF/PEEK thermoplastic composites

Consolidation of aerospace-grade high-temperature thermoplastic carbon fiber composites via Nano-engineered electrothermal heating

High Temperature Rheological Behavior and Sintering Kinetics of CF/PEEK Composites During Selective Laser Sintering

Efficient 3D temperature field prediction and visualization for AFP process analysis in composite structures

Parametric process optimisation of automated fibre placement (AFP) based AS4/APC-2 composites for mode I and mode II fracture toughness

Thermoplastic Composites Fiber Placement Process Research

Crystallization mechanism and mechanical properties of CF/PPS thermoplastic composites manufactured by laser-assisted automated fiber placement