Abstract:Abstract In a data center, electronic equipment such as server and switches dissipate heat and the corresponding cooling systems contribute to typically 25–35% of total energy consumption. The heat load continues to increase as there is a greater need for miniaturization and convergence. In 2014, data centers in the U.S. consumed an estimated 70 billion kWh, representing about 1.8% of total U.S. electricity consumption. Based on current trend estimates, U.S. data centers are projected to consume approximately 73 billion kWh in 2020 [1]. Many research and strategies are adopted to minimize energy cost. The recommended dry bulb temperature for long-term operation and reliability for air cooling is between 18–27°C and the largest allowable inlet temperature range to operate at is between 5°C and 45°C with American Society of Heating, Refrigeration, and Air-Conditioning Engineers (ASHRAE) enabling much broader allowable zones) [2]. But understanding a proper cooling system is very important especially for thermal management of IT equipment with high heat loads such as 1U or 2U multi-core, high-end servers and blade servers which provide more computing per watt. Many problems like high inlet temperature due to the mixing of hot air with cold air, local hot spots, lower system reliability, increased failure, and downtime may occur. Among many other approaches to managing high-density racks, in-row coolers are used in between racks to provide cold air and minimize local hot spots. This paper describes a computational study being performed by applying in-row coolers for different rack power configuration with and without aisle containment. The power, as well as the number of racks, are varied to study the effect of raised inlet temperature for the IT equipment in a Computational Fluid Dynamics (CFD) model developed in 6SigmaRoom with the help of built-in library items. A comparative analysis is also performed for a typical small-sized non-raised facility to investigate the efficacy and limitations of in-row coolers in thermal management of IT equipment with variation in rack heat load and containment. Several other aspects like a parametric study of variable opening areas of duct between racks and in-row coolers, the variation of operating flow rate and failure scenarios are also studied to find proper flow distribution, uniformity of outlet temperature and predict better performance, energy savings and reliability. The results are presented for general guidance for flexible and quick installation and safe operation of in-row coolers to improve thermal efficiency.

Thermal Full-Field Prediction of an Air-Cooled Data Center Using a Novel Multi-Scale Approach Based on POD and CFD Coupling

Analytical Modeling of Forced-Air Cooling Heatsink by Considering Air Temperature Rise in Channel and Coupling of Multiple Heat Sources

Multi-scale collaborative modeling and deep learning-based thermal prediction for air-cooled data centers: An innovative insight for thermal management

An open-source and experimentally guided CFD strategy for predicting air distribution in data centers with air-cooling

Numerical study of fluid flow and temperature distributions in a data center

Rapid simulation of outlet air temperature of racks in data centers

Conjugate Heat Transfer Modeling of a Cold Plate Design for Hybrid-Cooled Data Centers

Real-time optimization of the liquid-cooled data center based on cold plates under different ambient temperatures and thermal loads

Three computational methods for analysing thermal airflow distributions in the cooling of data centres

Hot spot temperature prediction and operating parameter estimation of racks in data center using machine learning algorithms based on simulation data

Experimental Research and Energy Effectiveness Analysis on Chip-Level Two-Stage Loop Thermosyphon System for Data Centre Free Cooling

A Simulation-Based Approach to Data Center Thermal Efficiency Optimization

An energy-environment coupled simulation framework for multi-scale and multi-facet evaluation of data center

An improved POD-Galerkin method for rapid prediction of three-dimensional temperature field for an IGBT module

Performance analysis and optimization of free cooling strategies for a liquid-cooled data center

The Numerical Simulation of the Airflow Distribution and Energy Efficiency in Data Centers with Three Types of Aisle Layout

Optimal thermal management on server cooling system to achieve minimal energy consumption based on air-cooled chiller

Development and validation of an open-source CFD model for the efficiency assessment of data centers

Thermal-Aware Task Placement with Dynamic Thermal Model in an Established Datacenter

Optimal Design and Modeling of Server Cabinets With In-Row Coolers and Air Conditioning Units in a Modular Data Center

Experimental study on the immersion liquid cooling performance of high-power data center servers