Abstract:Two-dimensional (2D) metal halide perovskites have recently emerged as promising photovoltaic materials due to their superior ambient stability and rich structural diversity. However, power conversion efficiencies (PCEs) of the 2D perovskites solar cells (PSCs) still lag behind their three-dimensional (3D) counterpart, particularly due to the anisotropy in the charge carrier mobility and inhomogeneous energy landscape. A promising alternative is Dion-Jacobson (D-J) phase quasi-2D perovskite, where the bulky organic diammonium cations are introduced into inorganic frameworks to remove the weak van der Waals interactions between interlayers and to improve the open-circuit voltage (Voc). Although the D-J phase 2D perovskite shows a homogeneous energy landscape and better charge transport, their poor crystallinity and existence of higher trap states remain a major challenge for the development of high-efficiency solar cells device. To address this issue, here, we report the eclipsed D-J phase 2D perovskite using 1,5-diaminonaphthalene cation and subsequently treated the film with ammonium thiocyanate (NH4SCN) additive to further improve the film crystallinity, out-of-plane orientation, and carrier mobility. We observe that 2 mol NH4SCN surface treatment in NDA-based D-J phase perovskite leads to better film morphology and improved crystallinity, as confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Time-resolved photoluminescence (TRPL) spectroscopy and steady-state space charge limited current (SCLC) mobility measurement reveal a significant reduction of trap-assisted nonradiative recombination and improvement of carrier mobility in the thiocyanate-passivated perovskite. Consequently, the PCE of the NH4SCN-treated (NDA)(MA)3(Pb)4(I)13 perovskite device enhanced nearly 46% from 10.3 to 15.08%. We have further studied intensity-dependent J-V characteristics, which demonstrate the reduction of ideality factor, confirming the effective suppression of trap-assisted nonradiative recombination, consistent with the transient PL results. Electrochemical impedance spectroscopy (EIS) confirms the improved charge carrier transport in NH4SCN additive-treated devices. Interestingly, our additive-engineered unsealed perovskite devices retained 75% of their initial efficiency after 1000 h of continuous storage under 60% relative humidity. This study opens up the strategy for developing high-efficiency and stable 2D perovskite solar cells.

Ammonium Thiocyanate Enhanced High-Performance Quasi-Two-Dimensional Perovskite Solar Cells

Synergistic Effects of the Physical Modification and Chemical Passivation Enabling Efficient Perovskite Solar Cells

Carbon Quantum Dot-Passivated Perovskite/Carbon Electrodes for Stable Solar Cells

Post‐Treatment Passivation by Quaternary Ammonium Chloride Zwitterion for Efficient and Stable Perovskite Solar Cells

Effective passivation of perovskite solar cells involving a unique secondary ammonium halide modulator

Chitosan Derivatives Modified with SnO 2 for High-Efficiency Carbon-Based Perovskite Solar Cells

Efficient and Stable CuSCN-based Perovskite Solar Cells Achieved by Interfacial Engineering with Amidinothiourea

Realizing High‐Efficiency Perovskite Solar Cells by Passivating triple cation perovskite films

Reducing surficial and interfacial defects by thiocyanate ionic liquid additive and ammonium formate passivator for efficient and stable perovskite solar cells

Synergistic effect of multifunctional MXene-nanosheet and naphthoquinone sulfonate toward high-performance perovskite solar cells and modules

SnO2-Perovskite Interface Engineering Based on Bifacial Passivation Via Multifunctional N-(2-Acetamido)-2-aminoethanesulfonic Acid Toward Efficient and Stable Solar Cells

Hexylammonium Iodide Derived Two-Dimensional Perovskite As Interfacial Passivation Layer in Efficient Two-Dimensional/Three-Dimensional Perovskite Solar Cells.

Thiocyanate-Passivated Diaminonaphthalene-Incorporated Dion-Jacobson Perovskite for Highly Efficient and Stable Solar Cells

Efficient and stable perovskite solar cells thanks to dual functions of oleyl amine-coated PbSO4(PbO)4 quantum dots: Defect passivation and moisture/oxygen blocking

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO2‐Based Electron Transport Layers

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Bidirectional Passivation for Highly Efficient and Stable CuSCN-Based Perovskite Solar Cells Using (3-Mercaptopropyl)trimethoxysilane

Aromatic carboxyl acid regulated nanoparticle deposition and passivation of tin oxide for high performance perovskite solar cells

Passivating Buried Interface Via Self-Assembled Novel Sulfonium Salt Toward Stable and Efficient Perovskite Solar Cells

Perovskite Surface Passivation Using Thiophene-Based Small Molecules for Efficient and Stable Solar Cells

Interface Modification by Ammonium Sulfamate for High‐Efficiency and Stable Perovskite Solar Cells