Abstract:Aspheric thin-walled crucibles with large diameters are widely used for photovoltaics and semiconductor industries, while they have hard-brittle and aspheric characteristics. Nevertheless, these crucibles strictly require atomic surfaces and high material removal rate (MRR). This is a challenge for chemical mechanical polishing (CMP). To break this challenge, a novel green CMP was developed for fused silica, containing ceria, lanthana, hydrogen peroxide, diethylene triaminepentaacetic acid pentasodium, carboxymethyl cellulose sodium and guanidine carbonate. After CMP, surface roughness Ra of 0.115 is obtained at a scanning area of 5 × 5 μm2 measured by atomic force microscopy, and MRR is 563 nm/min. In such an atomic surface, the MRR is the highest compared with those published previously. Transmission electron microscopy confirms that the thickness of damaged layer after CMP is only 2.63 nm. A novel approach of robot floating polishing is proposed for aspheric crucibles with a diameter of 810 mm and a height of 580 mm. Using the developed CMP, surface roughness Sa of 0.178 nm on inner surface of an aspheric thin-walled crucible is achieved under a measurement area of 50 × 50 μm2. X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance reveal that the content of Ce3+ increased from 28.54 to 43.76 %. Through Raman, XPS and Fourier transform infrared spectroscopy, CMP mechanisms are elucidated. Densified damaged layer on the surface of fused silica was induced by the transformation of surface structure from six-membered to four- or three-membered network. Ce-OH and Si-OH were formed between fused silica and ceria abrasives, forming Ce-O-Si by condensation reaction of dehydration. The developed green CMP and approach provide new pathway to polish and manufacture atomic surfaces for aspheric thin-walled crucibles with large diameters.

Novel Green Chemical Mechanical Polishing by Controlling Ph Values and Redox Reaction for Achieving Atomic Surface of a Nickel Alloy

Development of a novel chemical mechanical polishing slurry and its polishing mechanisms on a nickel alloy

Novel green chemical mechanical polishing for an aluminum alloy and mechanisms interpreted by molecular dynamics simulations and measurements

Angstrom surface on copper induced by novel green chemical mechanical polishing using ceria and silica composite abrasives

A Novel Approach of Chemical Mechanical Polishing for a Titanium Alloy Using an Environment-Friendly Slurry

Atomic surface induced by novel green chemical mechanical polishing for aspheric thin-walled crucibles with large diameters

Novel green chemical mechanical polishing of fused silica through designing synergistic CeO 2 /h-BN abrasives with lubricity

A review: green chemical mechanical polishing for metals and brittle wafers

Research on the Chemical Mechanical Polishing Process of Aluminum Alloy Wafers with Acidic Slurry

Electrochemical surface modification of GH4742 nickel-based superalloy in C6H5Na3O7 solution

Theoretical and experimental investigation of chemical mechanical polishing of W–Ni–Fe alloy

A nano-scale mirror-like surface of Ti–6Al–4V attained by chemical mechanical polishing

Chemical mechanical polishing of hard disk substrate with α-alumina-g-polystyrene sulfonic acid composite abrasive

A novel process of chemical mechanical polishing for FV520B steel

Nano-deformation of a Ni–P coating surface after nanoparticle impacts

Environment friendly chemical mechanical polishing of copper

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Chemical mechanical polishing for sapphire wafers using a developed slurry

A special electrostatic self-assembly structure of colloidal silica: Improving Chemical Mechanical Polishing performance

High-performance chemical mechanical polishing slurry for aluminum alloy using hybrid abrasives of zirconium phosphate and alumina

Novel Eco-friendly Slurries for Chemical Mechanical Polishing of GCr15 Bearing Steel