Abstract:Study on the corrosion behavior of reinforcing steel is one of the most significant research topics in the field of corrosion and protection of metals. The scanning microelectrode technique is a powerful tool to study localized corrosion behavior of reinforcing steel in a corrosive solution. In this work, the corrosion behavior of reinforcing steel in a simulated concrete pore solution with Cl - and the inhibition effect of a mixture of NaNO 2 and Na 2 SiO 3 on the steel were studied by the scanning microelectrode technique assisted by polarization curve measurements and surface analyses. Q235 reinforcing steel was used as the tested material. The cylindrical steel specimen with dimension of Æ1.14 cm ´ 0.50 cm was sealed in a PVC holder enveloped with epoxy resin, and only a cross section (1.00 cm 2 ) of the steel served as the working surface. Before experiments, the steel specimen was sequentially polished by silicon carbide sandpaper up to 1500 grit and 0.3 µm Al 2 O 3 powder, and then ultrasonically cleaned in deionized water and ethanol. A saturated Ca(OH) 2 solution was used as the simulated concrete pore (SCP) solution. The simulated polluted concrete pore (SPCP) solution was prepared from SCP solution by adjusting its pH to 11.50 with deionized water and adding 0.05 M NaCl. NaNO 2 and Na 2 SiO 3 with different concentrations as corrosion inhibitors were added to the SPCP solution. The potential distribution on the reinforcing steel surface was measured by a home-built scanning microelectrode measurement system. Ag/AgCl electrodes were used as a scanning microprobe and a micro-reference electrode. Polarization curve measurements were carried out by an Autolab Potentiostat Galvanostat. A three–electrode cell was used with the steel specimen as the working electrode, a saturated calomel electrode (SCE) as the reference electrode and a platinum electrode as the counter electrode. All the measurements were performed at ambient temperature. The results showed that there were no stable large potential peaks on the steel surface in the pure Ca(OH) 2 solution with pH 12.50 or 11.50, indicating that the steel surface was in a passive state and no corrosion took place. For the steel in the SPCP solution with 0.050 M NaCl and pH 11.50, a stable and large local potential peak occurred on its potential map after 20 min immersion. This result indicated that the steel was active and localized corrosion occurred resulting from the Cl - attack. For the SPCP solution with 0.004 M NaNO 2 and 0.001 M Na 2 SiO 3 , there were no stable potential peaks on the potential map of the steel immersed in the solution for 8 h, indicating that no localized corrosion took place. Therefore, the mixture of NaNO 2 with Na 2 SiO could protect the reinforcing steel from corrosion. The polarization curve measurements and surface analyses also confirmed the above results. This work was supported by the National Natural Science Foundation of China (Nos. 21073151, and 21173177).

Potential Utilization of Sludge Extract As Corrosion Inhibitor for Reinforcing Steel in Alkaline Environment

Corrosion Inhibition and Adsorption Behavior of (3-Aminopropyl)-triethoxysilane on Steel Surface in the Simulated Concrete Pore Solution Contaminated with Chloride

Effectiveness of an amine-based inhibitor—guanidine for steel in chloride-contaminated concrete

Study on Synergistic Corrosion Inhibition Effect between Calcium Lignosulfonate (CLS) and Inorganic Inhibitors on Q235 Carbon Steel in Alkaline Environment with Cl−

Effect of Cl− Accumulation on Corrosion Behavior of Steels in H2S/CO2 Methyldiethanolamine (MDEA) Gas Sweetening Aqueous Solution

Electrochemical performance of reinforcing steel in alkali-activated slag extract in the presence of chlorides

Synergistic inhibition of molybdate and phytate on chloride-induced corrosion of carbon steel in simulated concrete pore solutions

Seaweed Extract As Green Corrosion Inhibitor for Carbon Steel in Hydrochloric Acid Solution

Simulated pore water of chloride-contaminated concrete by means of electrochemical techniques

Study on Corrosion Inhibition of Reinforcing Steel in Simulated Concrete Pore Solutions by Scanning Microelectrode Technique

Utilization of Natural Soils as a Remediation Method for Electric Arc Furnace and Ladle Slags

Ammonium Phosphate as Inhibitor to Mitigate the Corrosion of Steel Rebar in Chloride Contaminated Concrete Pore Solution

EFFECTIVENESS OF MIGRATORY CORROSION INHIBITORS IN SIMULATED PORE WATER OF CHLORIDE-CONTAMINATED CONCRETE BY MEANS OF ELECTROCHEMICAL TECHNIQUES

Effectiveness Protection Performance of an Internal Blending Organic Corrosion Inhibitor for Carbon Steel in Chloride Contaminated Simulated Concrete Pore Solution

Novel sustainable corrosion inhibitors for enhancing carbon steel corrosion resistance based on clay and lignin biopolymer extracted from raw Alfa fibers

Alternanthera Philoxeroides Extract As a Corrosion Inhibitor for Steel in Cl3CCOOH Solution

A Study of Three Corrosion Inhibitors for Reinforcing Steel in SPS Solution by Electrochemical Methods

Betel Nut Shell Water Extract as a Green Corrosion Inhibitor for Q235 Steel in 1 M HCl

Sustainable Corrosion Inhibitor for Steel in Simulated Concrete Pore Solution by Maize Gluten Meal Extract: Electrochemical and Adsorption Behavior Studies

Synergistic Inhibition Effect of Sodium Tungstate and Hexamethylene Tetramine on Reinforcing Steel Corrosion

Preparation of Algae Extract as Green Corrosion Inhibitor for Q235 Steel in Chloride Ion Solutions