Abstract:With the increasing severity in the service environment of secondary refining furnaces, traditional refractories cannot meet the high requirements. MgO-based fired refractories are subject to the thermal shock effect and slag penetration which are detrimental to their performance. In this study, low-carbon MgO-based refractories are reinforced by an in-situ MgAl2O4(MA)-TiO2 dense layer with the addition of low-cost self-prepared titanium carbonitride [Ti(C, N)]. The influence of the addition of as-prepared Ti(C, N) on the properties of low-carbon MgO-based refractories was investigated. The reinforced refractories had no cracks after 190 thermal shock cycles, demonstrating the highest hot modulus of rupture (HMOR) with excellent thermal shock resistance (TSR). After 2.5 h of rotary immersion in a steel slag, the corrosion depth of the composites was only 26.3% of that of commercial MgO-CaO refractories. Based on the thermodynamic analysis, the Ti(C, N) reinforcement mechanism for the low-carbon MgO-based refractories was studied. A MA-TiO2 dense layer formed during the oxidation process of the composites which enhanced the oxidation resistance. The volume expansion caused by the partial oxidation of Ti(C, N) prevents the penetration of the molten slag to refractories and Ti(C, N) powders forming a protective layer to further effectively protect the composites from slag corrosion owing to its high surface area. In addition, 3CaO·2TiO2 formed by the reaction between the steel slag and Ti(C, N) further increased the slag corrosion resistance (SCR) of the composites. This research offers a new idea for the material selection for secondary refining furnaces to achieve a green and effective steel-making production route and enriches the understanding of the phase behaviour in the Mg-Al-Ti-C-O-N system under high temperatures.

Quantitative Assessment of Microporous MgO Castable Erosion and Corrosion Behaviors in Two Tundish Covering Fluxes

Slag Corrosion Behavior of Novel Lightweight Magnesia Castable in a High-Basicity Slag: Role of Micropores and Nanosized Zirconia

Simultaneous enhance of the thermal shock resistance and slag-penetration resistance for tundish flow-control refractories: the role of microporous magnesia

Fabrication of Y2O3-doped MgO Refractory Raw Materials Based on Magnesium Hydroxide from Salt-Lake Brine

Dynamic interaction of refractory and molten steel: Corrosion mechanism of alumina-magnesia castables

Corrosion of MgO-C with Magnesium Aluminate Spinel Addition in A Steel Casting Simulator

Corrosion mechanism of reactive MgO‐bonded Cr2O3‐bearing castables in CaO–Al2O3–Fe2O3–SiO2‐based steel‐making slag

Comparison study on effect of nano-sized Al2O3 addition on the corrosion resistance of microporous magnesia aggregates against tundish slag

Corrosion Resistance of MgO and Cr2O3-Based Refractory Raw Materials to PbO-Rich Cu Slag Determined by Hot-Stage Microscopy and Pellet Corrosion Test

Chemical attack of Al2O3-MgAl2O4 refractory castables in the non-slag-tapping side of refining ladle

Corrosion mechanism of cement-bonded Al2O3–MgAl2O4 pre-cast castables in contact with molten steel and slag

Elaboration of A Coupled Numerical Model for Predicting Magnesia Refractory Damage Behavior in High-Temperature Reactor

Microstructure evolution, mechanical characteristics and erosion behavior of Cr2O3–Al2O3–MgO–ZrO2 refractories in molten reduction slag

Development of an Ultra-Low Carbon MgO Refractory Doped with α-Al2O3 Nanoparticles for the Steelmaking Industry: A Microstructural and Thermo-Mechanical Study

Improved properties of in-situ MgAl2O4-TiO2 dense layer reinforced low-carbon MgO-based refractories

A Comparative Study of Corrosion Behavior of MgO-based Refractories in RH Snorkels: MgO-sintered MgAl2O4 Refractories and MgO-synthetic Mg1.08Al1.84Ti0.08O4 Refractories

Numerical Understanding on Refractory Flow-Induced Erosion and Reaction-Induced Corrosion Patterns in Ladle Refining Process

Structure and properties of lightweight magnesia refractory castables with porous matrix

A comparative study on the slag resistance of MgO–C, low‐carbon MgO–C, and MgO–SiC–C refractories

Wetting and corrosion behavior between magnesia–carbon refractory and converter slags with different MgO contents

Corrosion of MgO–C Refractory with Ladle Slags