Effects of Magnetic Field Direction on Texture Evolution in a Cold‐Rolled IF Steel Sheet During High Magnetic Field Annealing

Yan Wu,Changshu He,Xiang Zhao,Liang Zuo

DOI: https://doi.org/10.1002/9780470444191.ch49

2008-01-01

Abstract:This chapter contains sections titled: Introduction Materials and Methods Results and Discussion Summary Acknowledgement References

What problem does this paper attempt to address?

Microstructure and Texture Evolution in Cold Rolled Interstitial Free (IF) Steel Sheet during Annealing under AC Magnetic Field

Chang Shu He,Sadahiro Tsurekawa,Hiroyuki Kokawa,Xiang Zhao,Liang Zuo

DOI: https://doi.org/10.4028/www.scientific.net/msf.638-642.2781

2010-01-01

Materials Science Forum

Abstract:An AC magnetic field (0.5Tesla) is applied with the field direction perpendicular to the rolling direction during annealing of a 76% cold-rolled IF steel sheet. Microstructure and texture evolution in the as-annealed specimens were determined using SEM based OIM technique. It is found that the recrystallization is noticeably retarded by AC magnetic field annealing. At the early stage of recrystallization (annealing at 650°C for 30min), the development of (111) orientations was favored by the AC magnetic field. With progress of recrystallization (annealing at 700°C and 750°C for 30min), the applied AC magnetic field suppressed the development of γ-fiber recrystallization textures to some extent.
Characteristics of Recrystallization Texture Evolution in High Magnetic Field for Interstitial Free (IF) Steel Sheet

CS He,YD Zhang,X Zhao,L Zuo,C Esling

DOI: https://doi.org/10.4028/www.scientific.net/msf.495-497.465

2005-01-01

Abstract:High magnetic field is applied with the field direction parallel to the rolling direction during annealing of a cold rolled IF steel sheet. Results of X-ray ODF analysis show that, magnetic field annealing retards the normal recrystallization texture evolution for the IF steel sheet. It is worth noting that an abnormal increase of orientation intensity at {100}<110> is found after magnetic annealing for 25min at 650°C. When the magnetic field strength is increased from 10 Tesla to 14 Tesla, the a-fiber is further strengthened, especially the {100}<110> component. Combined with EBSD analysis results, it is considered that the magnetic field does not change the mechanism of recrystallization texture evolution for the IF steel sheet in the present case.
Texture and microstructure development in cold-rolled interstitial free (IF) steel sheet during electric field annealing

C.S. He,Y.D. Zhang,Y.N. Wang,X. Zhao,L. Zuo,C. Esling

DOI: https://doi.org/10.1016/s1359-6462(02)00552-3

IF: 6.302

2003-03-01

Scripta Materialia

Abstract:The effects of electric field annealing on the development of recrystallization texture and microstructure in a cold-rolled IF steel sheet were studied by means of ODF analysis and optical microscopy. Results showed that the applied external electric field might retard recrystallization, and enhance the γ-fiber recrystallization texture that is beneficial to the deep-drawability.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering
Effect of magnetic field on mechanical properties of an advanced high strength steel sheet

Ravi Datt Yadav,Vijay Gautam

DOI: https://doi.org/10.1016/j.matlet.2024.136087

IF: 3

2024-02-21

Materials Letters

Abstract:The present study deals with the experimental investigations during plastic deformation of a dual phase steel sheet in uniaxial tension under a magnetic field, applied in the longitudinal direction of the tensile specimen. To ascertain the changes in tensile properties, the experiments are performed with and without magnetic field. The microstructural and texture investigations are done using field emission scanning electron microscopy in the samples taken from the middle of the tensile tested with 20% of gauge length (20% engineering strain) with and without magnetic field. The results show an increase in compressive residual stress, microhardness and anisotropy of the sheet when tested with magnetic field which may affect the formability of tested sheet. It is also observed that the magnetic field affects the texture during plastic deformation and renders a strong texture as compared to that of specimen tested without magnetic field.

materials science, multidisciplinary,physics, applied
Effect of annealing temperature on magnetic and mechanical properties of twin-roll strip casting Cu-bearing non-oriented electrical steel

Yanqing Xu,Guoqing Zu,Jiangnan Liang,Yuqian Wang,Ying Han,Weiwei Zhu,Yu Zhao,Xu Ran

DOI: https://doi.org/10.1007/s10853-022-08097-5

IF: 4.5

2023-01-06

Journal of Materials Science

Abstract:The as-cast sheet of Cu-bearing non-oriented electrical steel with a width of 300 mm and a thickness of 2.4 mm was prepared by the twin-roll strip casting process. The effects of nucleation and growth of recrystallized grains at different annealing temperatures on the evolution of the microstructure and texture of annealed sheet were studied. In addition, the magnetic and mechanical properties of the final sheets were analyzed. The results show that the shear band in the cold-rolled sheet can promote the formation of {100} texture at the initial stage of recrystallization, regardless of high or low-temperature annealing. The combination of low-temperature nucleation and subsequent high-temperature growth is more conducive to the formation of strong {100} texture and has higher preparation efficiency than only through low-temperature annealing. It also indirectly indicates that moderate nucleation and preferential growth are important for the formation of strong beneficial texture. Combined with the subsequent aging treatment, the low-temperature nucleation sheet can obtain an excellent match between mechanical properties and magnetic properties.

materials science, multidisciplinary
Research Situation of Annealing Process for Non-oriented Electrical Steel

ZHANG Shuai,CAO Jianchun,LI Jun

DOI: https://doi.org/10.14158/j.cnki.1001-3814.2013.10.018

2013-01-01

Abstract:The effects of annealing temperature and time on the non-oriented electrical steel magnetic properties were reviewed.Annealing temperature and time mainly affects the different textures share and the grain sizes of non-oriented electrical steel respectively.Changes of the grain sizes also have a certain effect on textures formation.The highest point of the magnetic induction value in the fibrous tissue completely disappears and{111} plane texture has a lower state of the component content.Iron loss reduction mainly depends on the hysteresis loss reduction,the effects of textures are relatively small.
Cube Texture Development in Pure Ni during Annealing in a High Strength Magnetic Field

Xin Lu Li,Wei Liu,Andrew Godfrey,Qing Liu

DOI: https://doi.org/10.4028/www.scientific.net/MSF.495-497.1315

2005-01-01

Materials Science Forum

Abstract:A 10 Tesla magnetic field was applied during annealing of cold-rolled high purity Ni at 300 degrees C for 2 hours, with samples aligned at various different angles to the magnetic field direction. The effect of the magnetic field annealing on the cube texture evolution and the microstructural development was investigated by use of electron backscatter pattern (EBSP) analysis in the scanning electron microscope. The results show that both the cube texture evolution and the grain size are affected by the application during annealing of a high strength magnetic field, and that the effect varies as a function of the angle between the sample normal and the magnetic field direction. The cube texture volume fraction resulting from 2 hours annealing increases with increasing angle between the field direction and the sample normal direction, though in nearly all cases lower cube volume fractions were obtained compared to annealing without a magnetic field. The average size for all grains and for just cube-oriented grains both decrease with decreasing cube texture fraction, suggesting that the presence of a magnetic field either leads to enhanced recrystallization nucleation, or to a retardation of grain growth after recrystallization.
Effect of Annealing Temperature on Texture of Cold-Rolled IF Steel Rolled from Strip Hot-Rolled in Ferrite Region

LI Si-jun,QU Jia-hui,LIU Gang,WANG Fu,ZUO Liang

DOI: https://doi.org/10.3321/j.issn:0449-749x.2006.06.015

2006-01-01

Abstract:The effect of annealing temperature on fibrous texture of cold rolled IF steel sheet rolled from strip hot rolled in ferrite region was investigated.The results show that after annealing at 769 ℃,the component of α-fibrous texture is decreased to the minimum and {111}∥N.D.γ-fibrous texture becomes stronger,which is propitious to deep drawability.With the annealing temperature increasing,the component of α-fibrous texture is not changed,but the γ-fibrous texture is damaged.
Effect of Annealing Temperature and Time on the Magnetic Properties and Magnetic Anisotropy of a Temper-Rolled, Semi-processed Non-oriented Electrical Steel

Youliang He,Ruby Zhang,Tihe Zhou,Haden Lee,Chad Cathcart,Peter Badgley

DOI: https://doi.org/10.1007/s11837-023-06361-w

2024-01-14

JOM

Abstract:The effect of final annealing temperature and time on the core loss, magnetic permeability, and magnetic anisotropy of a temper-rolled, semi-processed 0.5 wt.% Si non-oriented electrical steel was investigated. The magnetic properties of the steel sheets at 50–400 Hz and 0.5–1.50 T were measured by the Epstein frame method on strips cut along both the rolling (RD) and transverse directions (TD). Optimal magnetic properties were obtained when the annealing temperature was at 800–825°C, and the annealing time was 2–4 h. Relatively large magnetic anisotropy between the RD and TD was observed in samples after recrystallization (~ 10% in core loss and ~ 70% in relative permeability), while deformed and non-recrystallized samples showed small anisotropy in magnetic properties. Regardless of the processing state of the steel, i.e., temper-rolled, recovered, or recrystallized, the core loss followed quadratic polynomial functions with respect to both the frequency and magnetic flux density, while the relative magnetic permeability followed cubic polynomial functions with respect to both the frequency and magnetic flux density. The microstructure and texture of selected samples were characterized by electron backscatter diffraction, which revealed the correlations between the magnetic properties of the steel and the microstructure and texture.

materials science, multidisciplinary,metallurgy & metallurgical engineering,mining & mineral processing,mineralogy
Effects Of Electric Field Annealing On Recrystallization Texture And Plastic Strain Ratio (R Value) Of If Steel Sheet

X. Zhao,C. S. He,J. Xu,L. Zuo

DOI: https://doi.org/10.4028/www.scientific.net/MSF.539-543.3478

2007-01-01

Abstract:Effects of electric field annealing on recrystallization texture and average plastic strain ratio (r value) of IF steel sheet were studied by mean of X ray diffraction ODF analysis and the tensile test. Specimens of 75% cold-rolled IF steel sheet were annealed at 850 degrees C for 25min,with and without electric field annealing respectively. Results show that the electric field annealing does not change the type of recrystallization texture and its formation mechanism in IF deep-drawing steel sheet, but improves the formation and development of recrystallization gamma-fiber texture, enhances the intensity of gamma-fiber texture, and retards the formation and development of a-fiber texture. Comparing with the conventional annealing, electric field annealing improves the average plastic strain ratio (r value). Possible reasons for the intensification of recrystallization gamma-fiber texture with the electric field applied may attribute to the reduction of stored energy, thus hindering the formation of other orientated nuclei and enhancing the nucleating ratio of gamma-oriented nuclei. And the intensification of recrystallization gamma-fiber texture was considered as the main reason for the enhancement of the plastic strain ratio (r value) in IF steel sheet.
An integrated exploration from microstructure to mechanics in austenite to pearlite transformation of high carbon steel under high magnetic fields

Yong Feng,Dong Zhang,Tingping Hou,Hang Xu,Xuan Liang,Xiangheng Xiao,Kaiming Wu

DOI: https://doi.org/10.1016/j.jmrt.2024.08.071

IF: 6.267

2024-09-02

Journal of Materials Research and Technology

Abstract:The effects of a high magnetic field (12 T) on the microstructural evolution and mechanical properties of high carbon steel during isothermal pearlitic transformation at 720 °C were investigated. The application of a high magnetic field effectively promotes pearlitic transformation and leads to a reduction in the lamellar spacing and the geometrically necessary dislocation density (GND) as well as to a slight increase in the grain size of the pearlite, which leads to a decrease in hardness. This is because the magnetic field reduces the magnetic Gibbs energy of ferrite and cementite, resulting in an increase in the driving force of phase transformation, which shortens the pearlite maturation time and reduces the nucleation barriers of pearlite, thereby accelerating the growth rate of pearlite. In addition, the interfacial energy of ferrite/cementite was found to be increased by the magnetic field from the thermodynamic point of view, and the mechanism of action of the magnetic field -induced precipitation of cementite in the form of particles and short rods was elucidated. The present work will enhance the understanding of the mechanism of magnetic field-induced phase transformation in iron-based materials.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Significant effect of as-cast microstructure on texture evolution and magnetic properties of strip cast non-oriented silicon steel

Haitao Jiao,Yunbo Xu,Wenzheng Qiu,Haijie Xu,R.D.K. Misra,Yifeng Du,Jianping Li,Guodong Wang

DOI: https://doi.org/10.1016/j.jmst.2018.05.007

IF: 10.319

2018-12-01

Journal of Materials Science and Technology

Abstract:In this study, two types of as-cast microstructure produced by strip casting were cold rolled and annealed to investigate the effect of initial microstructure on the textural evolution and magnetic properties of non-oriented silicon steel. The results indicated that the cold-rolled sheets of coarse-grained strip with pronounced {100} components exhibited stronger λ fiber (〈100〉//ND) and weaker γ fiber (〈111〉//ND) texture as composed to the fine-grained strip with strong Goss ({110}〈001〉) texture. After annealing, the former was dominated by η fiber (〈001〉//RD) texture with a peak at {110}〈001〉 orientation, while the latter consisted of strong {111}〈112〉 and relatively weak {110}〈001〉 texture. In addition, a number of precipitates of size ∼30–150 nm restricted the grain growth during annealing, resulting in recrystallization of grain size of ∼46 μm in the coarse-grained specimen and ∼41 μm in the fine-grained specimen. Ultimately, higher magnetic induction (∼1.72 T) and lower core loss (∼4.04 W/kg) were obtained in the final annealed sheets of coarse-grained strip with strong {100} texture.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Effect of Magnetic Field on Solidification Structure of A Centrifugal Cast High Speed Steel Roll

X. D. Zhang,W. Liu,Q. L. Li,A. Godfrey,Q. Liu

DOI: https://doi.org/10.1179/174328409x463063

IF: 1.8

2010-01-01

Materials Science and Technology

Abstract:The electromagnetic field exerted during solidification of a centrifugal cast high speed steel roll causes a marked variation in the structure. The type, size, distribution and volume fraction of carbides change with increasing magnetic field intensity. The appropriate external magnetic field (0·15 T in the present study) can refine carbides, break down carbides’ network on grain boundaries, make some carbides form in grains, distribute carbides more homogeneously on grain boundaries or in grains and improve overall bulk hardness. The application of external magnetic field can also refine grains, reduce retained austenite and improve matrix hardness. It can be expected that through inducing an appropriate external magnetic field during centrifugal casting these changes can give an improvement of properties of HSS rolls, such as wear resistance and thermal fatigue properties.
Effects of high magnetic field on isothermal pearlite transformation and microstructure in a hypereutectoid steel

junjie li,wei liu

DOI: https://doi.org/10.1016/j.jmmm.2014.03.006

IF: 3.097

2014-01-01

Journal of Magnetism and Magnetic Materials

Abstract:A high magnetic field was applied during the isothermal pearlite transformation of a hypereutectoid carbon steel at three different temperatures. It was found that the magnetic field applied can increase the transformation rate and the pearlite nodule growth rate, decrease the interlamellar spacing of pearlite and the amount of low angle boundary in ferrite lamella. The magnetic field effects are more obvious at high temperature. The mechanism of field-effect was discussed by analyzing the influences of high magnetic field on the eutectoid temperature, diffusion activation energy in austenite, Gibbs free energy of ferrite and dislocation mobility.
Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Hai-Tao Liu,Yin-Ping Wang,Ling-Zi An,Zhao-Jie Wang,Dao-Yuan Hou,Jun-Mou Chen,Guo-Dong Wang

DOI: https://doi.org/10.1016/j.jmmm.2016.07.034

IF: 3.097

2016-12-01

Journal of Magnetism and Magnetic Materials

Abstract:In this work, a 0.71wt%Si+0.44wt%Al as-cast strip was produced by novel twin-roll casting. Some as-cast samples were respectively reheated and hot rolled at different temperatures in order to obtain different microstructure prior to cold rolling and annealing. The effects of the hot rolled microstructure on microstructure, texture evolution and magnetic properties were investigated in detail. A coarse deformed microstructure with λ-fiber texture was formed after hot rolling at 850–1050°C, finally leading to an inhomogeneous recrystallization microstructure with strong λ-fiber, Goss and extremely weak γ-fiber texture. By contrast, a fine transformed microstructure was formed after hot rolling at 1150–1250°C, finally leading to a fine and homogeneous recrystallization microstructure with stronger α-fiber, γ-fiber and much weaker λ-fiber texture. It should be noted that both the magnetic induction and core loss non-monotonically decreased or increased according to the hot rolling temperature. The unfavorable α-fiber and γ-fiber textures in the annealed sheets were much weaker than those of the conventional products regardless of the hot rolling temperature, thus contributing to a much higher magnetic induction. However, the average grain size in the annealed sheets was much lower than those of the conventional products regardless of the hot rolling temperature, thus leading to a higher core loss except the case of 1050°C. Hence, it is underscored that better integrated magnetic properties than those of the conventional products can be obtained by optimizing the hot rolled microstructure to produce final desirable recrystallization microstructure and texture.

materials science, multidisciplinary,physics, condensed matter
The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

Yinghui Zhang,Jingfu Yang,Jing Qin,Haibin Zhao

DOI: https://doi.org/10.1088/2053-1591/abdb4f

IF: 2.025

2021-01-01

Materials Research Express

Abstract:Abstract Thin-gauge non-oriented electrical steel was processed by one-stage cold rolling using different normalizing time, and the through-process texture evolution was studied. Strong {411}〈148〉 recrystallization textures were obtained in sheets subjected to longer normalization time. After cold rolling reduction, the initial {411}〈148〉 texture transformed to {114}〈110〉 and {311}〈136〉 textures. As the rolling reduction increased, the {311}〈136〉 texture transformed into a {112}〈110〉 texture, but not a {111}〈112〉 texture. In normalized sheets with large grains, more shear bands formed during cold rolling, which provided more nucleation sites for {100}〈013〉 oriented grains. The nucleation sites of {100}〈013〉 grains existed at {112}〈110〉 and {100}〈011〉 deformed grain boundaries and in the {112}〈110〉 and {111}〈112〉 orientation shear bands. Strong {100}〈013〉 textures formed due to the high mobility and large grain size. As the normalizing time increased, the magnetic properties were greatly improved in the final annealed sheets. The superior magnetic induction was due to the strong {100}〈013〉 and {210}〈001〉 textures and the weak {111}〈112〉 texture. A larger grain size and weaker γ texture reduced the hysteresis loss, which caused low core losses in the final annealed sheets.

materials science, multidisciplinary
Effect of a Magnetic Field on Phase Transformation of Steel

Liu W.,Ou D. R.,Zhou H. H.,Tang G. Y.,Wu F.

DOI: https://doi.org/10.1557/jmr.2001.0313

2001-01-01

Abstract:Electromagnetic theory is used to characterize the magnetization processes in metals and alloys. The analysis shows that the free energy of a phase transformation may be reduced or enhanced by the magnetic field depending on the ratio of the permeability of the old and new phases. This means that the magnetic field can either stimulate or inhibit the nucleation process. The theory is in accord with the experimental results by others and us.
Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

Hao-Ze Li,Hai-Tao Liu,Zhen-Yu Liu,Hui-Hu Lu,Hong-Yu Song,Guo-Dong Wang

DOI: https://doi.org/10.1016/j.matchar.2013.11.014

IF: 4.537

2014-02-01

Materials Characterization

Abstract:An Fe-6.5wt.% Si-0.3wt.% Al as-cast sheet was produced by twin-roll strip casting process, then treated with hot rolling, warm rolling and annealing. A detailed study of the microstructure and texture evolution at different processing stages was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction analysis. The initial as-cast strip showed strong columnar grains and pronounced <001>//ND texture. The hot rolled & warm rolled sheets were characterized by large amounts of shear bands distributed through the thickness together with strong <110>//RD texture and weak <111>//ND texture. After annealing, detrimental <111>//ND texture almost disappeared while beneficial {001}<210>, {001}<010>, {115}<5 −10 1> and {410} <001> recrystallization textures were formed, thus the magnetic induction of the annealed sheet was significantly improved. The recrystallization texture in the present study could be explained by preferred nucleation and grain growth mechanism.

materials science, multidisciplinary,metallurgy & metallurgical engineering, characterization & testing
Effect of cold drawing reduction rate on edge-to-center-characterized microstructure and orientation alongside residual stresses in conjunction with magnetic properties of low-carbon high-alloy ferromagnetic steel

Shahab Bazri,Carlo Mapelli,Silvia Barella,Andrea Gruttadauria,Davide Mombelli,Renato Nemfardi,Roberto Bedini,Giorgio Zucchelli

DOI: https://doi.org/10.1016/j.jmmm.2023.171699

IF: 3.097

2024-01-05

Journal of Magnetism and Magnetic Materials

Abstract:In the current research, the effect of cold drawing reduction rate (CDRR) of 15% and 45% and the required subsequent isothermal static recrystallization annealing heat treatment (ISRAHT) on the microstructures, textures, residual stresses, and magnetic properties of ferritic/ferromagnetic stainless steel (FSS), EN 1.4106, are investigated by a series of experimental analyses. The study is carried out by the theoretical well-known model of Johnson-Mehl-Avrami-Kolmogorov (JMAK) in conjunction with aforesaid properties. According to the results, by increasing the CDRR, the recrystallization fractions (RF) become faster in accordance with the JMAK theory. Such an increment also affects more fragmented and elongated grains, which leads to provide smaller grains in size. However, by the effect of slow cooling process (SCP), the grain growth is another noticeable part of study. Likewise, the effects of CDRR and the subsequent ISRAHT find to be beneficial for the evolution of microstructures, textures, and relief of residual stresses, and better performance of magnetic behavior. For instance, higher relative magnetic permeabilities approximately above 1000 causes to reach residual stresses closer to zero. The cold-drawn FSSs are consisted of the α -fibre texture, which is close to {2 2 3} 〈1 1 0〉 and {1 1 1} 〈1 1 0〉, with higher intensity while by gradual higher recrystallization, the orientation tendency to {1 1 1} 〈0 1 1〉 of γ -fibre are formed following to the more distributed texture with lesser intensity. The findings display that while the recrystallization process addresses the formation of new grains, resulting in the more equiaxed grains, more well-aligned textures are also achieved in respect to the lower misorientation uniformity density and even with more distributed clusters.

materials science, multidisciplinary,physics, condensed matter
Effect of magnetic field on microstructure and mechanical properties of austempered 70Si3MnCr steel

Bilal Nawaz,Xiaoyan Long,Zhinan Yang,Jiali Zhao,Fucheng Zhang,Junkui li

DOI: https://doi.org/10.1016/j.msea.2019.05.023

2019-01-01

Abstract:The effect of magnetic field on bainite microstructure and mechanical properties of 70Si3MnCr steel was studied. Microstructure observation shows that introducing magnetic field during the austempering process, the microstructure was significantly refined and the volume fraction of the bainitic ferrite was increased. The high nucleation rate for bainitic ferrite caused by the high magnetostatic energy should be responsible for this positive effect. As compared with samples without magnetic field treatment, the magnetic samples also show a simultaneously increased strength and ductility. The ultra-fine bainitic ferrite with higher dislocation density, in magnetic samples increased the tensile strength, and carbon-riched filmy retained austenite and small blocky retained austenite in magnetic samples have a tremendous effect on ductility. High magnetic strength in magnetic samples increases the strength of the bainitic ferrite, which acts as a stress shielding source to prevent the retained austenitic phase from higher stress and increase the plasticity. Moreover, high magnetic strength can alter the spins of the free radicals between the dislocations and obstacles from S state to T state which had weak bonding with dislocations. Hence, depinning of dislocations is facilitated which results in increased plasticity. Therefore, due to the magnetoplasicty, high magnetic properties, and ultra-fine microstructure, magnetic samples show a more excellent strength and ductility as compared with the normal samples.

Effects of Magnetic Field Direction on Texture Evolution in a Cold‐Rolled IF Steel Sheet During High Magnetic Field Annealing

Microstructure and Texture Evolution in Cold Rolled Interstitial Free (IF) Steel Sheet during Annealing under AC Magnetic Field

Characteristics of Recrystallization Texture Evolution in High Magnetic Field for Interstitial Free (IF) Steel Sheet

Texture and microstructure development in cold-rolled interstitial free (IF) steel sheet during electric field annealing

Effect of magnetic field on mechanical properties of an advanced high strength steel sheet

Effect of annealing temperature on magnetic and mechanical properties of twin-roll strip casting Cu-bearing non-oriented electrical steel

Research Situation of Annealing Process for Non-oriented Electrical Steel

Cube Texture Development in Pure Ni during Annealing in a High Strength Magnetic Field

Effect of Annealing Temperature on Texture of Cold-Rolled IF Steel Rolled from Strip Hot-Rolled in Ferrite Region

Effect of Annealing Temperature and Time on the Magnetic Properties and Magnetic Anisotropy of a Temper-Rolled, Semi-processed Non-oriented Electrical Steel

Effects Of Electric Field Annealing On Recrystallization Texture And Plastic Strain Ratio (R Value) Of If Steel Sheet

An integrated exploration from microstructure to mechanics in austenite to pearlite transformation of high carbon steel under high magnetic fields

Significant effect of as-cast microstructure on texture evolution and magnetic properties of strip cast non-oriented silicon steel

Effect of Magnetic Field on Solidification Structure of A Centrifugal Cast High Speed Steel Roll

Effects of high magnetic field on isothermal pearlite transformation and microstructure in a hypereutectoid steel

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

Effect of a Magnetic Field on Phase Transformation of Steel

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

Effect of cold drawing reduction rate on edge-to-center-characterized microstructure and orientation alongside residual stresses in conjunction with magnetic properties of low-carbon high-alloy ferromagnetic steel

Effect of magnetic field on microstructure and mechanical properties of austempered 70Si3MnCr steel