Abstract:The effect of porosity in composite materials has been studied for years due to its deleterious effects on mechanical properties, especially matrix dominated properties. Currently there is an increasing use of composites in infrastructure worldwide, for example bridge components, residential and building structures, marine structures such as piers and docks, and large industrial chemical tanks. Most of these applications use fiberglass composites. Unfortunately, most of the published literature has focused on carbon fiber composites, in which fiber diameter and gas-fiber interactions are different than fiberglass composites. Therefore, the present study was undertaken to revisit the effect of porosity but specifically in fiberglass composites. The goal of this experimental study was to implement and evaluate various methods for creating porosity in fiberglass composites in a controlled manner in terms of obtaining repeatable void content, morphology, and location within the laminate. The various methods included using different amounts of autoclave pressure, adding a small amount of water between prepreg layers, and using dry fabric layers to starve the laminate of resin. Ultrasonic C-scan nondestructive evaluation was used to assess the quality of the cured panels, as well as optical and electron microscopy and void content measurements via resin burn-out. The cured panels were mechanically tested using the short beam shear (SBS) method. The results showed that the water spray method proved to be the best in terms of producing noticeably different levels of porosity, although the panels required drying to remove residual water after cure. The voids from all three techniques were either oval or elongated in-plane between the plies, but they were not uniformly distributed in-plane. The use of C-scan proved to be helpful for characterizing overall uniformity of each panel, although the results could not be used to directly compare void content between panels. The use of SBS testing was successful for evaluating void dominated properties in panels with high void content, although it was not very sensitive to coupons with lower void contents. Several interesting observations are offered in this manuscript of the fracture surface details and their relation to the SBS load deflection curves. Overall, it was found that the failure mechanisms were mixed mode and the voids did not serve as failure initiation sites. However, the voids participated mainly in the horizontal propagation of cracks between layers, presumably making it easier when they were intersected by a crack and reducing SBS strength.

Carbon Fiber Composite Voids and Testing Methods

Porosity Test in Carbon Composites Based on a New Ultrasonic Attenuation Method

Pulse-echo Based Ultrasonic Attenuation Model for Porosity Test of Carbon Fiber Composites

Ultrasonic attenuation testing method for NDE of void content based on theoretical model and experiment calibration

Cfrp Voids 3d Identification and Location Method Based on the Process of Backscattered Signal

Development of Portable Ultrasonic Non-Destructive Test System for Viod Content of Carbon-Fiber Reinforced Plastics

Ultrasonic attenuation model of void contained carbon-fiber reinforced plastics

Frequency Spectral Analysis for the Ultrasonic Attenuation of Carbon Fiber Reinforced Plastics

Thickness Measurement of Composite Material Using Eddy Current Testing

Critical Void Content for Thermoset Composite Laminates

A Nonlinear Method for Characterizing Discrete Defects in Thick Multilayer Composites

Voids in fiber-reinforced polymer composites: A review on their formation, characteristics, and effects on mechanical performance

Evaluation of porosity effects on the mechanical properties of carbon fiber-reinforced plastic unidirectional laminates by X-ray computed tomography and mechanical testing

Investigation of various techniques for controlled void formation in fiberglass/epoxy composites

Micro‐mesoscopic analysis of 3D void formation and evolution in CFRP composite using high‐resolution x‐ray microtomography

Research Development of Ultrasonic Testing Methods in Composite Materials for Porosity Measurement

Study on Void Formation in Multi-Layer Woven Fabrics

Effect of Manufacturing Defects on Mechanical Properties and Failure Features of 3D Orthogonal Woven C/C Composites

Nondestructive testing and evaluation techniques of defects in fiber-reinforced polymer composites: A review

Identification of Localized Void Defects in Composite by Recurrence Quantification Analysis of Ultrasonic Backscattered Signal

Research on Void Dynamics during In Situ Consolidation of CF/High-Performance Thermoplastic Composite