Abstract:It is expected that the demand for Metal Matrix Composite (MMCs) will increase in these applications in the aerospace and automotive industries sectors, strengthened AMC has different advantages over monolithic aluminium alloy as it has characteristics between matrix metal and reinforcement particles. However, adequate joining technique, which is important for structural materials, has not been established for (MMCs) yet. Conventional fusion welding is difficult because of the irregular redistribution or reinforcement particles. Also, the reaction between reinforcement particles and aluminium matrix as weld defects such as porosity in the fusion zone make fusion welding more difficult. The aim of this work was to show friction stir welding (FSW) feasibility for entering Al 6061/5 to Al 6061/18 wt. % SiCp composites has been produced by using stir casting technique. SiCp is added as reinforcement in to Aluminium alloy (Al 6061) for preparing metal matrix composite. This method is less expensive and very effective. Different rotational speeds,1000 and 1800 rpm and traverse speed 10 mm \ min was examined. Specimen composite plates having thick 10 mm were FS welded successfully. A high-speed steel (HSS) cylindrical instrument with conical pin form was used for FSW. The outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt. %) was 195 MPa at rotation speed 1800 rpm, the outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt.%) was 165 MPa at rotation speed 1000 rpm, that was very near to the composite matrix as-cast strength. The research of microstructure showed the reason for increased joint strength and microhardness. The microstructural study showed the reason (4 %) for higher joint strength and microhardness. due to Significant of SiCp close to the boundary of the dynamically recrystallized and thermo mechanically affected zone (TMAZ) was observed through rotation speed 1800 rpm. The friction stir welded ultimate tensile strength Decreases as the volume fraction increases of SiCp (18 wt.%).

Weldability and Friction-stir-welding of Particles Reinforced Aluminum Metal Matrix Composites

Friction Stir Welding of AZ31B Magnesium Alloy with 6061-T6 Aluminum Alloy: Influence of Processing Parameters on Microstructure and Mechanical Properties

Study on the Microstructure and Mechanical Properties on Al/Carbon Fiber Reinforced Thermoplastic Dissimilar Friction Stir Lap Welding Joints

Friction stir lap welding for dissimilar materials of aluminum alloy and carbon-fiber-reinforced polyetherimide

A Review on Friction Stir Welding of High-Strength Al-Zn-Mg Alloy: Insights on Second-Phase Particles

Experimental Review on Friction Stir Welding of Aluminium Alloys with Nanoparticles

Recent Advances in Friction Stir Welding/Processing of Aluminum Alloys: Microstructural Evolution and Mechanical Properties

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

Microstructure evolution and mechanical properties of CNT/Al composite joints via friction stir welding

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of in Situ Al3Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Friction stir welding of aluminium hollow extrusion: weld formation and mechanical properties

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Influence of Welding Combined Plastic Forming on Microstructure Stability and Mechanical Properties of Friction Stir-Welded Al-Cu Alloy

Metallurgical Reaction and Joining Phenomena in Friction Welded Al/Fe Joints

Impact of friction stir welding parameters and Al2TiO5 reinforcement on the mechanical, wear, and corrosion performance of dissimilar welded aluminium composite joints

Friction stir spot welding of 5052 aluminum alloy to carbon fiber reinforced polyether ether ketone composites

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of In Situ Al 3 Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Formation Mechanism of Thicker Intermetallic Compounds in Friction Stir Weld Joints of Dissimilar AA2024/AZ31B Alloys

Optimizing Friction Stir Welding of Dissimilar Grades of Aluminum Alloy Using WASPAS

Microstructure and mechanical properties of friction stir welded powder metallurgy AA2024 alloy

A critical review on mechanical and microstructural properties of dissimilar aluminum (Al)-magnesium (Mg) alloys