FAAS Determination of Trace Amounts of Silver by Standard Addition

Jin Xie

2001-01-01

Abstract:In this paper a method is studied for the flame atomic absorption spectrometry determination of trace amounts of silver by standard addition.No separation is needed and the method is rapid,simple with few interferences.It has been applied to the direct determination of trace amounts of silver in different sarnples with satisfactory results.

What problem does this paper attempt to address?

Flame atomic absorption spectrometric determination of silver in geological materials using a flow-injection system with on-line preconcentration by coprecipitation with diethyldithiocarbamate

Shiqiao Pei,Zhaolun Fang

DOI: https://doi.org/10.1016/0003-2670(94)80193-2

IF: 6.911

1994-01-01

Analytica Chimica Acta

Abstract:Trace amounts of silver in geological samples were determined by flame atomic absorption spectrometry. The analyte was preconcentrated and separated from the bulk of the matrix by on-line coprecipitation with the iron(II)-diethyldithiocarbamate complex in the presence of 1,10-phenanthroline in a flow-injection system. The precipitate was collected in a knotted reactor without using a filter. The precipitate was dissolved in isobutyl methyl ketone and introduced directly into the nebulizer-burner system of an atomic absorption spectrometer. 1,10-Phenanthroline was added to the sample solution to mask large concentrations of iron(II). The tolerance of the method for iron was thus increased to 4 g 1−1. An enhancement factor of 26 and a concentration efficiency of 28 min−1 were obtained for a coprecipitation time of 45 s, resulting in a sampling frequency of 62 h−1. The detection limit (3σ) in the sample solution of 0.5 μg 1−1. The relative standard deviation at the 30 μg 1−1 level was 2.1%. The analytical results obtained for geological reference materials were in good agreement with the certified values.
Determination of Trace Silver in Waste Water by 9,10‐dimethylacridinium Fluorosulfonate‐k2s2o8 Chemiluminescence System

Jin‐Ming Lin,Fan Zhang

DOI: https://doi.org/10.1002/cjoc.19910090604

IF: 5.56

1991-01-01

Chinese Journal of Chemistry

Abstract:AbstractA new highly sensitive method for determination of trace silver in waste water with 9,10‐dimethylacridinium fluorosulfonate (DAFA)‐K2S2O8 system was suggested. In the basic aqueous solution, trace of silver (I) showed strongly catalytic effect on the chemiluminescence system with the presence of 2,2′‐bipyridine. The range of the linear relationship between light intensity and concentration of silver (I) is 1.0 × 103 mol / L to 6.0 × 103 mol / L. The detection limit is 8.0 × 103 mol / L, and the RSD for 5.0 × 103 mol / L Ag (I) is 6.5% (n=13). In the existence of potassium fluoride, the selectivity is higher. Combining the treatment with nitric acid, the method is applied to determine some environmental waste water and the results are similar to atomic absorption spectroscopy.
Microanalysis for Flame Atomic Absorption Spectroscopyin Determination of High Content Sodium

DAI Yu-ting,GAO Min,DAI Jun-xiao

2013-01-01

Abstract:A new method using Flame Atomic Absorption Spectroscopy(FAAS) and Microanalysis to determine high content sodium is developed.The developed method involves the choosing of suitable absorption line of sodium,the optimization of testing parameters and the evaluation of the linearity of the method.The linearity is 0~5 mg/L,the detection limit is 0.02 mg/L and the repeatability is 0.5% RSD.By comparing the measured sodium content with its truth value in some known organic and inorganic compounds,the absolute error is less than 0.3%,the relative error is less than 1%,and the recovery is 99.2%~100.6%.
[Determination of Trace Lead in Copper by Enhancing Effect FAAS-using Derivative Technique].

H Sun,L Chen,J Sun

1998-01-01

Abstract:A new method for the determination of trace lead in copper is proposed by enhancing effect-flame atomic absorption spectrometry using derivative technique. Enhancing effect of matrix Cu on lead was investigated. The sensitivity for lead was enhanced 17 times than that of conventional flame atomic absorption spectrometry by combining derivative technique with matrix Cu enhancing effect. Determination result is satisfactory by this method with 0.007 microg/mL detection limit and 0.7% RSD.
Investigation of Dispersive Solid-Phase Extraction Combined with Slurry Sampling Thermospray Flame Furnace Atomic Absorption Spectrometry for the Determination of Cadmium

Shengchun Yang,Siyu Jiang,Kan Hu,Xiaodong Wen

DOI: https://doi.org/10.1016/j.microc.2019.104542

IF: 5.304

2020-01-01

Microchemical Journal

Abstract:In this work, a sensitive method for the determination of cadmium by flame atomic absorption spectrometry (FAAS) was established by combining dispersive solid-phase extraction (DSPE) with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS). Nano-TiO2 was used as adsorbent, and the dispersive extraction simplified the operation procedure. Through the application of slurry sampling, the on-line combination of DSPE with TS-FF-AAS was established and the time-consuming elution step after DSPE was avoided. Problems of nebulization associated with previous methods based on the coupling of FAAS and SPE were overcome. DSPE combined with TS-FF-AAS significantly improved the analytical performance of the modified FAAS, which established a sensitive method for the determination of cadmium based on FAAS. Under the optimal conditions, the limit of detection (LOD) was 0.04 mu g/L, which was better by an enhancement factor of 56. Compared to direct FAAS, the factor was 596. The method was applied to the determination of environmental water samples with satisfactory results.
Determination of Silver in Metal Plating Wastewater by Slotted Quartz Tube Flame Atomic Absorption Spectrometry (SQT-FAAS) after Preconcentration with Stearic Acid-Coated Magnetite Nanoparticle-Based Solid-Phase Microextraction (SA-MNP-SPME)

Hakan Serbest,Sezgin Bakırdere,Seyfullah Keyf

DOI: https://doi.org/10.1080/00032719.2021.1986718

2021-11-02

Analytical Letters

Abstract:Here is reported the determination of silver at ultratrace levels by slotted quartz tube-flame atomic absorption spectrometry (SQT-FAAS) following stearic acid coated magnetic nanoparticle based solid phase microextraction (SA-MNP-SPME). The parameters affecting silver extraction were optimized to obtain high efficiency. In addition to the magnetic property of iron oxide (Fe3O4) nanoparticles, they were coated with stearic acid to increase the surface area and the capacity for the analyte. An external magnetic field was used to separate the silver from the liquid phase. To obtain the highest efficiency, the mass of magnetic nanoparticles, pH and volume of buffer solution, mixing type and period, volume of eluent and volume of sample were optimized univariately. Under the optimum conditions, the limits of detection and quantitation were determined to be 40 and 130 ng L−1, respectively. Recovery experiments were performed to investigate matrix effects on the developed method by spiking real samples. Recoveries were between 96.3 and 105.1% with low standard deviations by the matrix matching calibration. The developed MNP-SPME-SQT-FAAS method achieved 305-fold improvement in detection power. These results demonstrated the method’s applicability for the determination of trace silver in complex samples with good accuracy and precision.
Determination of cadmium in biological materials by flame atomic absorption spectrometry with flow-injection on-line sorption preconcentration

Fang Zhaolun, Xu Shukun,Dong Liping, Li Wenqing

DOI: https://doi.org/10.1016/0039-9140(94)00204-5

IF: 6.1

1994-01-01

Talanta

Abstract:A new on-line preconcentration flame atomic absorption spectrometry (FAAS) system for trace element determination was developed based on sorption of soluble metal complexes on the walls of a PTFE knotted reactor using flow injection techniques. The system was applied to the determination of cadmium in biological materials. Cadmium complexed with sodium diethyldithiocarbamate was sorbed on the inner walls of the reactor and eluted on-line by isobutyl methyl ketone. The retention efficiency was 81% at a sampling loading rate of 5.2 ml/min. The enhancement factor was 66 and the concentration efficiency was 61/min with a 50 sec preconcentration period, consuming 4.2 ml sample. A detection limit of 0.1 mu g/l. Cd (3 sigma) was obtained with a sampling frequency of 55/hr. The precisions were 1.2% RSD for 20 mu g/l. Cd (N = 11). Thiourea and ascorbic acid/phenanthroline were used to overcome interferences from copper and iron, respectively. The analytical results obtained for powdered rice and human hair standard reference materials were in good agreement with the certified values.
Contents Determination of Copper in Chinese Traditional Medicines by FAAS

LIU Yue-cheng,WANG Shang-zhi,MENG Shuang-ming,GUO Yong,WU Yue-fang

2006-01-01

Abstract:The method for the determination of trace Cu in Chinese tradition medicine by flame atomic absorption spectrometry was determined in this paper,these samples are treated with HNO_3: HClO_4(4:1).The method is convenient and the results show good precision and accuracy.The detection limit was 0.0059μg/ml,the relative standard deviation of Cu was 7.45%,the rate of recovery were 92.3～110%.
Determination of trace cobalt, nickel and cadmium by on-line flow injection analysis with coprecipitation preconcentration FAAS

Liping Dong,Zhaolun Fang

1994-01-01

Abstract:An efficient on-line coprecipitation system was developed for flame atomic absorption spectrometry (FAAS) by using a flow injection technique. The cobalt, nickel and cadmium are coprecipitated with ammonium pyrrolidinedithiocarbamite (APDC)-Fe complex, and the precipitate is collected on a knotted reactor (KR) made of 250cm long and i.d.=0.5mm PTFE tube without filter. The precipitate is dissolved by MIBK and directly introduced into the spectrometer. The enhancement factors are 42, 30 and 33 for Co, Ni and Cd respectively, and the corresponding detection limits are 1, 3 and 0.3��g/L respectively. The RSD are 2.3% for 20.0 ��g/L Co, 2.0% for 100��g/L Ni, and 2.4% for 10.0 ��g/L Cd. The analytical results obtained for determining Co in standard reference bovine liver (NBS1577a) and Ni, Cd in standard reference urine (GBWO9103) agree well with the recommended values.
Flame Atomic Aabsorption Spectrometric Determination of Gold by Solid Phase Extraction Using Modified Nanometer Titanium Dioxide as Sorbent

Weijuan Liu,Yiran Xu,Yun Dai,Yaming Wang,Qiufen Hu

2009-01-01

Asian Journal of Chemistry

Abstract:The nanometer titanium dioxide immobilized on silica gel (NTDS) loaded with 5-(2-hydroxy-5-nitrophenylazo)-thiorhodanine (HNATR) was prepared and its solid phase extraction of gold was investigated. Gold could be adsorbed quantitatively when the gold-bearing samples flew through the column in 1.0 mol/L in phosphoric acid medium. The gold enriched on the column was eluted with 0.1 mol/L of sodium thiosulfate, realizing the high enrichment factor of low concentration gold and the separation of most interfering ions. Gold in the eluant was measured by flame atomic absorption spectrometry. Under the chosen experimental conditions, Beer's law was obeyed in the range of 0.05-3.0 mu g/mL for Au(III) with the correlation coefficient (r) of 0.9996. This method was used to determination of gold in ore and environmental waste samples with RSD in the range of 2.2-3.2% and addition recovery of 88-104%.
ONLINE ELECTROLYTIC DISSOLUTION OF SOLID METAL SAMPLES AND DETERMINATION OF COPPER IN ALUMINUM-ALLOYS BY FLAME ATOMIC-ABSORPTION SPECTROMETRY

DX YUAN,XR WANG,PY YANG,BL HUANG

DOI: https://doi.org/10.1016/S0003-2670(00)82541-6

IF: 6.911

1991-01-01

Analytica Chimica Acta

Abstract:A flow-injection system was developed in which alloy metal samples are electrolytically dissolved and the dissolved samples are analysed by flame atomic absorption spectrometry (FAAS). The effects of electrolyte composition and electrolysis parameters on the dissolution of the sample were studied. The method was used for the determination of copper in aluminium alloys. Electrolyte solutions consisting of 0.2-1.0 M nitric acid are better than other electrolytes tested with regard to both alloy sample dissolution and determination of copper by FAAS. The peak height increases linearly with the electrolysis time or current within a certain range. The detection limit depends on the sensitivity of the detector used, and can be improved by increasing the electrolysis time or current. Generally, aluminium alloys containing 0.5-10% copper can give suitable signals for FAAS determination. The reproducibility of electrolysis and determination is about 4% for the same sampling points and 5% for different sampling points on the alloy sample.
Determination Of Trace Silver By Solid Surface Room Temperature Phosphorimetry

Jiaming Liu,Tianlong Yang,Guohui Zhu,Yan Fu,Longdi Li

DOI: https://doi.org/10.3321/j.issn:0253-3820.2003.06.002

IF: 1.193

2003-01-01

Chinese Journal of Analytical Chemistry

Abstract:A new solid surface room temperature phosphorimetry for determination of trace silver was established with filter paper as a solid substrate. It is based on the fact that when AgCl.polyvinyl alcohol (PVA) . Ag+ adsorbs fluorescein anion(Fin(-)) to form the ion association complex (AgCl . PVA . Ag+ . Fin-), which corresponds to the end point of Fajans method in the presence of PVA, and the ion association complex can emit strong room temperature phosphorescence signal on the paper substrate. Under certain experimental condition, the phosphorescence intensity of the ion association complex is proportional to the adsorbed amount of Ag+, the linear range for Ag+ is 1.72 similar to 8.6 (10(-12) g/spot, 0.4 muL) and the regression equation is DeltaI(P) = 280.81 + 35.45 m(Ag+) (10(-12) g/spot), with a correlation coefficient r = 0.9995 (n = 6). This method is easy and fast to operate, and the determination results of silver in hair and tea samples are satisfactory.
Determination of Micro Zn in Common Salt Byflame Atomic Absorption Spectrometry

陈文军,何立峰,陈涛,刘林正,张海燕

DOI: https://doi.org/10.3969/j.issn.1005-5320.2005.01.019

2005-01-01

Abstract:A method has been studied for the determination of micro Zinc in common salt by flame atomic absorption spectrometry. The interference from background absorption of NaCl could be eliminated by adding equal NaCl in standard solution. The method is convenient and the concentration of Zinc was found in the range of 0.02～0.8 mg/L. RSD was less than 3%.
Flow injection on-line dilution for flame atomic absorption spectrometry by micro-sample introduction and dispersion using syringe pumps

Guanhong Tao,Zhaolun Fang,Joern Baasner,Bernhard Welz

DOI: https://doi.org/10.1016/S0003-2670(03)00086-2

IF: 6.911

2003-01-01

Analytica Chimica Acta

Abstract:A robust flow injection (FI) on-line dilution system based on micro-sample introduction was developed for flame atomic absorption spectrometry (FAAS). Two computer programmed and stepper-motor driven syringe pumps were used for the precise and reproducible sample metering in micro-liters and carrier delivery. Factors, which might influence the performance of the system, such as sample matrix and carryover, were investigated. No inferior effects were observed with various matrices including 10% glycerol. Sample carryover effects were less than 0.4%, tested by analyzing a blank and a sample alternately. Dilution factors were decided and keyed in manually. The system was calibrated using a set of concentrated standard solutions for a given dilution factor. At a sampling frequency of 60h−1, precisions were better than 2% R.S.D. (n=40) for dilution factors of 10–2000. The long-term stability of the system was examined by continuously running the system for a whole working day, and a precision of 2.6% R.S.D. (n=345) was obtained at a dilution factor of 1000. The system was verified by analyzing a standard copper alloy with a certified concentration of 57.4% Cu, resulting in a measurement solution with 574mgl−1 Cu.
Determination of Trace Elements in Tea by Suspension Sampling-Flame Atomic Absorption Spectrometry

高俊,徐建强,郑朝月

2012-01-01

Abstract:A method that a 1.5 g/L agar solution as suspension,determination of trace elements in tea,such as cadmium,lead,zinc,copper,and manganese with direct injection flame atomic absorption spectrometry was described.The impact on the measurement results for sample particle size and other factors was discussed.After optimization,the method elements spiked recoveries were in the range of 95.7%~105.6% and precision(RSD) was less than 10%.The method was simple,rapid,high efficiency,accurate results and reliable,compared with the traditional digestion method.
DIRECT DETERMINATION OF TRACE AMOUNTS OF METAL ELEMENTS IN WATER BY DERIVATIVE FAAS

Wei Wang,Han Sun

2001-01-01

Abstract:It is reported that by the use of the derivative atomic absorption spectrometry, the sensitivity of determination of some of the metal elements (Cu、 Mn、 Fe、 Zn、 Cd、 Pb) can be remarkably improved. The optimum condition for the determination was studied thoroughly. The extents of the raising of sensitivities of the above mentioned elements are found to be 20~50 times higher as compared with the conventional FAAS methods. The limits of detection are also much lower, improved to the extent of 5 to 11 times. This method has been applied to the analysis of water with recoveries in the range of 90.0%~110.0%.
Investigation of Thermospray Flame Furnace Atomic Absorption Spectrometric Determination of Cadmium Combined with Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction

Shengchun Yang,Haixiong Liu,Kan Hu,Qingwen Deng,Xiaodong Wen

DOI: https://doi.org/10.1080/03067319.2020.1723566

2020-01-01

International Journal of Environmental Analytical Chemistry

Abstract:Ultrasound-assisted dispersive liquid-liquid microextraction (UA-DLLME) was combined with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) for the first time to develop a highly sensitive method for the determination of cadmium. Ultrasound was used to assist the liquid phase extraction, replacing the traditional disperser solvent. A self-assembled TS-FF-AAS instrument was adopted to improve the analytical performance of traditional flame atomic absorption spectrometry (FAAS), and the characteristic of micro-injection is fully suitable to be coupled with UA-DLLME. The developed combination significantly improved the analytical performance of TS-FF-AAS and traditional FAAS, while overcoming problems of nebulisation associated with the coupling of FAAS and liquid phase extraction methods. Some environmental water samples were collected and analysed by the developed coupling with satisfactory results.
Sequential and Rapid Determination of Metallic Elements in Monosodium Glutamate by Continuum Source Flame Atomic Absorption Spectrophotometry

Jian-ping ZHANG,Shang-long CHEN,En-qi LIU,Xiao-dong HUANG

DOI: https://doi.org/10.3969/j.issn.1000-9973.2013.11.020

2013-01-01

Abstract:An effective method is developed for sequential and rapid determination of metallic elements in monosodium glutamate by continuum source flame atomic absorption spectrophotometry.The samples are digested by microwave.The testing results are affected by determination parameters of acetylene-air flow and burner height.The optimum determination parameters are chosen by experiments.Under the optimum work conditions,the content of Ca,Fe,Mg,Zn in monosodium glutamate is183.3,1.1,54.7,1.4μg/g respectively.The recoveries for the samples are from 95.9%to 107.4%.The precision relative standard deviations are from 1.2%to 1.9%for determining Ca,Fe,Mg,Zn.Therefore,this method is rapid,accurate,stable and with less pollution,and it has a high practical value.It provides scientific basis for sequential and rapid determination of muti-elements in food.
Determination of trace copper and nickel in environmental and biological samples by flow injection on-line microcolumn preconcentration flame AAS using acrylic acid-grafted polytetrafluoroethylene fiber for column packing

ZhaoHui Wang,Zhipeng Wang,Zhengpu Zhang,LiWen Liu,Xiuping Yan

2005-01-01

Atomic Spectroscopy

Abstract:A newly prepared acrylic acid-grafted PTFE fiber sorbent (see reference 20) was extended to flow injection (FI) on-line micro-column preconcentration - flame atomic absorption spectrometric determination of trace copper and nickel in environmental and biological samples. On-line preconcentration of trace analytes was achieved on the microcolumn packed with acrylic acid-grafted PTFE fibers, and the retained analytes were eluted with 1.0 mol L-1 HCl for on-line. FAAS determination. The optimum pH range of the sample solution for preconcentration of Cu(II) and Ni(II) was 3.6-5.6 and 4.4-6.4, respectively. The developed sorbent exhibited fairly fast kinetics for the adsorption of Cu(II) and Ni(II), permitting the use of high sample flow rates up to at least 10.8 ml, min(-1) for the FI on4ine microcolumn preconcentration system without loss of the retention efficiency. With a preconcentration time of 45 s at a sample loading flow rate of 10 mL min(-1), an enhancement factor of 48 for Cu and 23 and a detection limit (3sigma) for Ni, of 0.20 mug L-1 for Cu and 0.25 pg L-1 for Ni were achieved at a sample throughput of 55 h(-1). Precision for 11 replicate measurements of 25 mug L-1 Cu and 30 mug L-1 Ni was 1.2 and 1.6% (RSD), respectively. The method was successfully applied to the determination of trace copper and nickel in environmental and biological samples.
A Reliable and Straightforward Combination of vortex-assisted Dispersive Magnetic solid-phase Extraction with Direct Sorbent Sampling for Highly Sensitive Silver Determination in Water Samples Using Flame and Metal Furnace AAS

Diego Prudencio dos Santos,Milena do Prado Ferreira,Kristiany Moreira Diniz,Mariana Gava Segatelli,Eduardo Costa de Figueiredo,César Ricardo Teixeira Tarley

DOI: https://doi.org/10.1007/s00128-024-03955-1

2024-09-23

Bulletin of Environmental Contamination and Toxicology

Abstract:In the present paper, the assessment of vortex-assisted dispersive magnetic solid-phase extraction using amino-functionalized mesoporous combined with direct magnetic sorbent sampling (DMSS) in flame or furnace atomic absorption spectrometry (FAAS or FF-AAS) was demonstrated for highly sensitive silver determination in water samples. The developed method showed significant enrichment factors compared to conventional pneumatic nebulization by FAAS, 607 for DMSS-FF-AAS and 114 for DMSS-FAAS. The analytical curve showed linearity in the range from 5.0 to 70.0 μg L − 1 and 1.0 to 15.0 μg L − 1 and limits of detection of 0.59 and 0.09 μg L − 1 for DMSS-FAAS and DMSS-FF-AAS, respectively. The intra and inter-day precision evaluated as a percentage of the relative standard deviation (RSD,%) ranged from 1.89 to 4.71% for levels of 25.0 and 65.0 μg L − 1 . The method was applied in different kinds of water samples without matrix effects, yielding recovery values from 90 to 110%.

environmental sciences,toxicology

FAAS Determination of Trace Amounts of Silver by Standard Addition

Flame atomic absorption spectrometric determination of silver in geological materials using a flow-injection system with on-line preconcentration by coprecipitation with diethyldithiocarbamate

Determination of Trace Silver in Waste Water by 9,10‐dimethylacridinium Fluorosulfonate‐k2s2o8 Chemiluminescence System

Microanalysis for Flame Atomic Absorption Spectroscopyin Determination of High Content Sodium

[Determination of Trace Lead in Copper by Enhancing Effect FAAS-using Derivative Technique].

Investigation of Dispersive Solid-Phase Extraction Combined with Slurry Sampling Thermospray Flame Furnace Atomic Absorption Spectrometry for the Determination of Cadmium

Determination of Silver in Metal Plating Wastewater by Slotted Quartz Tube Flame Atomic Absorption Spectrometry (SQT-FAAS) after Preconcentration with Stearic Acid-Coated Magnetite Nanoparticle-Based Solid-Phase Microextraction (SA-MNP-SPME)

Determination of cadmium in biological materials by flame atomic absorption spectrometry with flow-injection on-line sorption preconcentration

Contents Determination of Copper in Chinese Traditional Medicines by FAAS

Determination of trace cobalt, nickel and cadmium by on-line flow injection analysis with coprecipitation preconcentration FAAS

Flame Atomic Aabsorption Spectrometric Determination of Gold by Solid Phase Extraction Using Modified Nanometer Titanium Dioxide as Sorbent

ONLINE ELECTROLYTIC DISSOLUTION OF SOLID METAL SAMPLES AND DETERMINATION OF COPPER IN ALUMINUM-ALLOYS BY FLAME ATOMIC-ABSORPTION SPECTROMETRY

Determination Of Trace Silver By Solid Surface Room Temperature Phosphorimetry

Determination of Micro Zn in Common Salt Byflame Atomic Absorption Spectrometry

Flow injection on-line dilution for flame atomic absorption spectrometry by micro-sample introduction and dispersion using syringe pumps

Determination of Trace Elements in Tea by Suspension Sampling-Flame Atomic Absorption Spectrometry

DIRECT DETERMINATION OF TRACE AMOUNTS OF METAL ELEMENTS IN WATER BY DERIVATIVE FAAS

Investigation of Thermospray Flame Furnace Atomic Absorption Spectrometric Determination of Cadmium Combined with Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction

Sequential and Rapid Determination of Metallic Elements in Monosodium Glutamate by Continuum Source Flame Atomic Absorption Spectrophotometry

Determination of trace copper and nickel in environmental and biological samples by flow injection on-line microcolumn preconcentration flame AAS using acrylic acid-grafted polytetrafluoroethylene fiber for column packing

A Reliable and Straightforward Combination of vortex-assisted Dispersive Magnetic solid-phase Extraction with Direct Sorbent Sampling for Highly Sensitive Silver Determination in Water Samples Using Flame and Metal Furnace AAS