Development and Application of Experimental Equipment for Fieldbus Control System

Hairong Zheng

2005-01-01

Abstract:This paper introduced the development and application of a fieldbus control experimental system based on EtherNet,ProfiBus and DeviceNet.On the background of the experiment,it described the basic methods of configuring hardware and software and some problems which should be paid attention to in mapping address.

What problem does this paper attempt to address?

Survey on Control Research of Networked Control Systems Based of Field Bus

LIU Gui-guo,LIU He,HUANG Dao

DOI: https://doi.org/10.3969/j.issn.1671-9565.2006.01.015

2006-01-01

Abstract:In view of control,the research background and contents on the networked control systems based of field bus are introduced in this paper.Networked control systems is a discipline as the combination of network and control science which covers a wide subjects.First,the three mathematic models of networked control systems are discussed, which consist of short network-induced delay with the controller time or event driven,and long network-induced delay with the controller event driven.Second,the mean value controllability,mean square controllability, mean value observability and mean square observability of networked control systems are analyzed. Third,several methods of controller design under the conditions of networked systems are intrduced.Finally.a further discussion on performance improvement of networked control systems in the furture is proposed.
EPA-based Open Network Control System

Dongqin Feng,Wenjun Huang,Jianxiang Jin,Jian Chu

DOI: https://doi.org/10.1109/icca.2003.1595168

2003-01-01

Abstract:The Ethernet is more and more used in the industrial environments. Because of the non-deterministic protocol of CSMA/CD, Ethernet is thought not to be suitable for the control of real time applications. With the worldwide application and development of Ethernet, its transmission rate is considered sufficiently high enough to estimate that all messages can be received inside a predefined temporal window. Especially, using Ethernet in industrial network will brings a lot of advantages: (1) consistency with the other communication systems installed in the enterprise; (2) employment of the same hardware all over the factory; (3) short cycle-times due to the high transmission speed; (4) large availability of chips implementing the MAC protocol, etc. In this paper, we first analyze the real-time capability of Ethernet and features of traffic for industrial network. Then, we propose some technologies for the design of an Ethernet-based real-time application. Finally, we present an EPA (Ethernet for Plant Automation)-based open network control system.
Networked Control System Design and Implementation

JM Zhang,SQ Wang

DOI: https://doi.org/10.1109/icmlc.2002.1174479

2002-01-01

Abstract:At present, the distribution of a control system based on a network is a "hot" research subject in the field of process control. This paper designs and implements a network-based process control system, which possesses functions such as remote control, clock synchronization, and a friendly man-machine interface. Simulation results over a university campus network confirm that the network-based control system is feasible and effective.
The Design of Host-Computer Software for the EPA Control Net

TAO Li,FENG Dong-qin,JIN Jian-xiang,CHU Jian

DOI: https://doi.org/10.3969/j.issn.1000-0682.2006.05.006

2006-01-01

Abstract:This paper presents a design conception for a hostcomputer software system applicable to the EPA industrial control net.This software system comprises configuration software,monitor software and database along with a kind of additional net management software.The paper also makes studies of the design of the function and program frame-work of the net management software,and puts forward a feasible project for implementation.
Exploration of Experiment Teaching on Electrical Equipment Computer Control

Jian-yong ZHAO,Hui-fen LU,Zai-ping PAN

DOI: https://doi.org/10.3969/j.issn.1008-0686.2014.03.025

2014-01-01

Abstract:In this paper,the importance of Electrical Equipment Computer Control course in electrical engineering teaching is expounded,and the innovative experimental platform is built according to content and characteristics. Then,the hardware structure and software environment are demonstrated in detail. The application of experimental platform in teaching verifies that it plays a positive role in students′ innovative training.
Construction of the process control experimental system based on EPA fieldbus

Yu-fang ZHONG

DOI: https://doi.org/10.3969/j.issn.1002-4956.2008.02.022

2008-01-01

Abstract:This paper introduces the EPA system architecture and presents an experiment process control system based on EPA fieldbus.On the background of temperature object control system,the realization of cascade control system using EPA fieldbus devices has been described,and the experimental application demonstrates the effectiveness of the proposed results.This innovated system can help students to understand the EPA fieldbus further,grasp specific control engineering knowledge and provide a new platform for scientific research.
Real-time scheduling scheme for EPA networks

Lu Li,Feng Dongqin,Chu Jian,Zhang Han

2009-01-01

Abstract:The existing problems and possible solutions of the networked control system(NCS) are summarized.Aiming at the problems of the induced delay and lack of the certainty and real-time control of fieldbus control systems based on Ethernet transmission,this paper proposes a real-time scheduling scheme for EPA(Ethernet for plant automation) industrial fieldbuses.This scheme provides a scheduling algorithm with time division multiple access and clock synchronization that improve the determinism of systems.Parallel processing takes advantage of system resources and produces a more accurate scheduling.The scheme can also process periodic and non-periodic data packets at the same time.Experimental results on an FPGA test platform show the effectiveness of the design.
The Implementation and Performance Analysis of an Ethernet Embedded System Based on a Microcontroller

刘康,王宣银

DOI: https://doi.org/10.3969/j.issn.1000-0682.2004.01.010

2004-01-01

Abstract:This paper presents an ethernet controller consisting of the RTL8019AS and the implementing of the TCP/IP in an embeded microcontroller system,which usually has a limit memory space.The remote data communication between the user and the RS-485 field bus has been realized in this system along with the analysis of its performance.
Design and implementation of controller for a sensor network protocol

Chunhua Ju,Xin Yuan,Jianguo Xing,WenMin Zhao,Weiwei Zhu,Jing Huang

2007-01-01

Abstract:This paper presents the design and implementation of network controller which based on the Data Link Layer's specification of a lightweight sensor-oriented fieldbus protocol, that is sensor network protocol. The controller is packed with AVALON standard peripheral interface. It can be treated as a normal intellectual property core in project design, so that the operation on it is simplified as reading or writing on register. The test results show that the controller meets the requirements of the specification in the frame identification, arbitration, checking and so on. A follow-up application developing basement can be found easily on this controller.
The development of a field controller based on industrial ethernet

Xiao-xia WANG,Wen-jun HUANG,Guo-qing ZHONG,Jian-xiang JIN

DOI: https://doi.org/10.3969/j.issn.1000-0682.2005.06.005

2005-01-01

Abstract:In accordance with the requirement of real-time control in the current industrial automation field,a solution to a field controller based on an industrial ethernet is offered,and several significant problems in the field controller are analyzed and solved.The field controller performs excellently in real-time property,openness,reliability,mathematical operation and multi-bus integration.
Design and Implementation of Field Bus Device Management System Based on HART Protocol

Tao Li,Ze Dong

DOI: https://doi.org/10.1109/imcec.2018.8469220

2018-01-01

Abstract:The highway addressable remote transducer (HART) was introduced in detail, on the basis, a field bus device management system based on HART protocol was designed. This system adopt C/S mode, and has the function of reading, writing as well as diagnosis, adjustment and management of devices parameters. Meanwhile, this article focus on solving the situation when there is no EDDL file, which is realizing the management of HART universal devices and HART dedicated devices based on the classification of commands in the HART protocol in order to complete the test and make the system to be steady state finally.
Developing a field controller based on the EPA industrial ethernet

Wenjun Huang,Jianxiang Jin

DOI: https://doi.org/10.19650/j.cnki.cjsi.2006.08.030

2006-01-01

Abstract:The basic architecture of EPA industrial Ethernet and the network control system is introduced, an advanced field controller solution is proposed based on EPA industrial Ethernet and CompactPCI internal bus. Several key technical issues of the field controller are analyzed and solved including real-time communication, deterministic communication and fieldbus integration. The proposed network control system features excellent performance in its openness, reliability, runtime computing capability, and etc.
Measurement and Control System Based on PROFIBUS Field Bus

WANG Xing-hai,WANG Shu-wei,CHEN Jing

DOI: https://doi.org/10.3321/j.issn:1000-7857.2006.08.014

2006-01-01

Abstract:A measurement and control system based on PROFIBUS field bus was designed for TRPO process, with WinPLC7 and KingView 5.0. The experiments were carried out with automation control system and good results were obtained.
Applied Fieldbus into Communication Systems in ITS

Min Li,Hui Wang,Ping Li

DOI: https://doi.org/10.3969/j.issn.1002-0268.2001.06.021

2001-01-01

Abstract:After the communication system in ITS is introduced briefly, its hierarchy of the communication system is presented. By analyzing the strong and weak points of standardized fieldbus, a new hierarchy communication system framework is presented in the paper, in which the widely accepted standards of higher layer are kept unchanged while the lower layer taking a new solution based on modified fieldbus. In order to demonstrate the feasibility, a prototype system is introduced.
Improvement of Experimental Teaching Device for Detection Technology Couse Based on Profibus

吴飞青,马修水,李林功,李英道,钟伟红,章旭峰

DOI: https://doi.org/10.3969/j.issn.1008-3634.2010.04.025

2010-01-01

Abstract:To increase the fieldbus experiments,a distributed control system was designed based on Profibus to improve the current experimental teaching system,which included Siemens PLC S7 315-2DP(main station),PIO-AI20 analog signal collector(slave station),CP-PB-1.0 Communications Controller,4-channel analog output module and 16-channel digital output module.In order not to affect the function of the original equipments,the relays were used to fulfil electrical isolation.The field test shows that the original and new systems can work single-handedly and keep stable,which proves the feasibility and effectiveness of the improving method.
The system of temperature calibration and controlling based on the fieldbus

CHI Xiang-li,WANG Jun-jie

DOI: https://doi.org/10.3969/j.issn.1671-1041.2006.04.020

2006-01-01

Abstract:Described in the article are the aspects of the PROFIBUS field bus system as well as its application in the experiment system of temperature calibration and controlling. The network structure, soft/hardware configuration and the main function are also elaborated.
The Remote Fan Control Based on Real-Time Ethernet

XIE Mingwei,ZHU Rusong,GU Zhenghua

DOI: https://doi.org/10.3969/j.issn.1009-671x.2011.02.06

2011-01-01

Abstract:To overcome the bad real-time performance of remote control system usually used in industrial field,a method is given to implement remote control based on real-time Ethernet,which combines real-time Ethernet,virtual instrument and optic fiber transmission.The result of experiment indicates that the remote control system based on real-time Ethernet has high reliability,better real-time performance and stronger anti-jamming ability,compared with the common PLC remote control system.It has great value in the control of large industrial field.
Research And Development of Industrial EtherNet

陈一雷,王俊杰

DOI: https://doi.org/10.16628/j.cnki.2095-8188.2002.05.011

2002-01-01

Abstract:In this paper, the advantages and disadvantages of the EtherNet application for industrial field were firstly summarized, and the structures of EtherNet in industrial field were illustrated.The emphasis on several design methods of industrial EtherNet based on“Transparent Factory” were introduced, and the merits and flaws of each method were analyzed.Finally,a few important technical requirements for the design of industrial EtherNet was pre sented.
A Basic Study on Algorithm of Real-Time Schedule Table for Fieldbus

JM Chen,Z Wang,YX Sun

DOI: https://doi.org/10.1109/wcica.2002.1021384

2002-01-01

Abstract:For a field-level industrial network, the real-time characteristic is very important. Fieldbuses are typical industrial control networks and their real-time characteristic mainly depends on the temporal property of the MAC protocol, which also is requirement of a distributed computer control system. Both WorldFIP and FF are the most important fieldbuses by their character of adopting a schedule table (ST) to control the real-time communication of tasks. This paper mainly introduces the characteristic of the ST algorithm, including establishing and optimizing it, and how to use it to support real-time communication in an industrial control network.
Application of Fieldbus Technology in Substation Integrated Automation System

Danyang Li,Chundong Song,Lili Xu

DOI: https://doi.org/10.18686/AHE.V4I12.3203

2021-03-24

Abstract:The development of fieldbus technology is an industrial data bus technology in the field of electrical engineering and automation. It can solve the problem of digital communication between intelligent instruments, controllers, actuators and other field devices. In addition, it can also effectively solve the problem of information transmission between these field control devices and advanced control systems. This paper analyzes the application of this technology combined with a number of engineering examples.

Engineering,Computer Science

Development and Application of Experimental Equipment for Fieldbus Control System

Survey on Control Research of Networked Control Systems Based of Field Bus

EPA-based Open Network Control System

Networked Control System Design and Implementation

The Design of Host-Computer Software for the EPA Control Net

Exploration of Experiment Teaching on Electrical Equipment Computer Control

Construction of the process control experimental system based on EPA fieldbus

Real-time scheduling scheme for EPA networks

The Implementation and Performance Analysis of an Ethernet Embedded System Based on a Microcontroller

Design and implementation of controller for a sensor network protocol

The development of a field controller based on industrial ethernet

Design and Implementation of Field Bus Device Management System Based on HART Protocol

Developing a field controller based on the EPA industrial ethernet

Measurement and Control System Based on PROFIBUS Field Bus

Applied Fieldbus into Communication Systems in ITS

Improvement of Experimental Teaching Device for Detection Technology Couse Based on Profibus

The system of temperature calibration and controlling based on the fieldbus

The Remote Fan Control Based on Real-Time Ethernet

Research And Development of Industrial EtherNet

A Basic Study on Algorithm of Real-Time Schedule Table for Fieldbus

Application of Fieldbus Technology in Substation Integrated Automation System