Abstract:The large extensional viscosity of dilute polymer solutions has been shown to dramatically delay the breakup of jets into drops. For low shear viscosity solutions, the jet breakup is initially governed by a balance of inertial and capillary stresses before transitioning to a balance of viscoelastic and capillary stresses at later times. This transition occurs at a critical time when the radius decay dynamics shift from a 2/3 power law to an exponential decay as the increasing deformation rate imposed on the fluid filament results in large molecular deformations and rapid crossover into the elasto-capillary regime. By experimental fits of the elasto-capillary thinning diameter data, a relaxation time of less than 100 μs has been successfully measured. In this paper, we show that, with a better understanding of the transition from the inertia-capillary to the elasto-capillary breakup regime, relaxation times close to 10 μs can be measured with the relaxation time resolution limited only by the frame rate and spatial resolution of the high speed camera. In this paper, the dynamics of drop formation and pinch-off are presented using dripping onto substrate capillary breakup extensional rheometry (CaBER-DoS) for a series of dilute solutions of polyethylene oxide (PEO) in water and in a viscosified water and glycerin mixture. Four different molecular weights between 100 k and 1 M g/mol were studied with varying solution viscosities between 1 and 22 mPa s and at concentrations between 0.004 and 0.5 times the overlap concentration, c*. The dependence of the relaxation time and extensional viscosity on these varying parameters was studied and compared to the predictions of dilute solution theory while simultaneously searching for the lower limit in solution elasticity that can be detected. For PEO in water, this limit was found to be a fluid with a relaxation time of roughly 20 μs. These results confirm that CaBER-DoS can be a powerful technique characterizing the rheology of a notoriously difficult material to quantify, namely, low viscosity inkjet printer inks.

Effect of Pre-Made Compatibilizer and Reactive Polymers on Polymer Drop Breakup

Effect of Premade Compatibilizer and Reactive Polymers on Polystyrene Drop Deformation and Breakup in Simple Shear

Erosion and breakup of polymer drops under simple shear in high viscosity ratio systems

Parallel Breakup of Polymer Drops under Simple Shear

Effect of Mixing Protocol on Compatibilized Polymer Blend Morphology

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Sheet formation during drop deformation and breakup in polyethylene/polycarbonate systems sheared between parallel plates

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Visualization of Poly(ether Imide) and Polycarbonate Blending in an Internal Mixer

Dual Effects of Compatibilizer on the Formation of Oriented Ribbon-Like Dispersed Phase Domains in Polystyrene/polyamide 6 Blends

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

Drop breakup dynamics of dilute polymer solutions: Effect of molecular weight, concentration, and viscosity

Compatibilization and morphology development of immiscible ternary polymer blends

A Vitrimer Acts as a Compatibilizer for Polyethylene and Polypropylene Blends

Fragmentation effect of solvent in recovery of unsaturated polyester resin and its composites

Concept of Reactive Compatibilizer-Tracer for Discovering Interfacial Reaction and Morphology Development for In-Situ Compatibilizing Blending Processes

Effect of Compatibilizer on the Transfer and Tribological Behaviors of PA46/HDPE Polyblends

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend

Role of compatibilizer in multicomponent polymer mixtures under shear flow