Abstract:To develop multifunctional microwave absorbing (MA) materials, foamed ceramics (FCs) with adequate MA performance that can withstand temperatures up to 1000 °C were prepared by sintering at 1200 °C with Si3N4 as the foaming agent and steel wires (alloy designation 0Cr18Ni9) as the absorber. The FCs with 0.2 vol% wires of 100 μm diameter and 3.0–4.0 mm length showed excellent MA performance in the 8.0–18.0 GHz frequency range. The entire reflectivity–versus–frequency curve was below –10 dB and contained a mean reflectivity as low as –15.3 dB and a minimum reflectivity of –22.4 dB at 17.7 GHz, indicating that more than 97.0% of the 8.0–18.0 GHz microwave was absorbed and the 17.7 GHz microwave was absorbed by about 99.4%. The FCs exhibited a high total/closed porosities of 87%/85%, low density of 0.36 g/cm3, relatively high compressive strength of 6.3 MPa, low thermal conductivity of 0.124 W/mK, and microstructure with uniformly–distributed pores with diameters less than 0.5 mm. After 100 h of heat–treatment at 1000 °C, the FCs remained largely unchanged in MA performance and physical–mechanical properties owing to their almost unchanged wire distribution, phase composition, and foam structure, implying that the FCs are a promising multifunctional MA material with the advantages of light weight, thermal insulation, and temperature resistance.

Design and Performance of Lightweight High–temperature Resistant Microwave Penetrating Foamed Ceramics

Low-temperature Co-Fired Ceramics with High Thermal Expansion and Reliability for Millimeter-Wave Antennas

Microwave absorbing performance and temperature resistance of multifunctional foamed ceramics prepared by the sintering method

Fabrication and performance of SiO2-based electromagnetic wave penetrating foamed ceramics with dense surface

Preparation and Performance of Electromagnetic Wave Absorbing Foamed Ceramics with High Closed Porosity and Gradient SiC Distribution

Bidirectional periodic pore structure Si-C-N multiphase ceramic with high thermostability and excellent microwave absorption properties over a wide temperature range

High Quality Microwave Dielectric Ceramic Sintered at Extreme-Low Temperature below 200° and Co-Firing with Base Metal

Low temperature fired CaF2-based microwave dielectric ceramics with enhanced microwave properties

Foaming Performance of the Closed–pore Foamed Ceramics Using Silicon Nitride As a Foaming Agent and Sodium Tetraborate As a Modifier of Foaming

High temperature stable, amorphous SiBCN microwave absorption ceramics with tunable carbon structures derived from divinylbenzene crosslinked hyperbranched polyborosilazane

All-ceramics with Ultrahigh Thermal Conductivity and Superior Dielectric Properties Created at Ultralow Temperatures

Preparation mechanism and properties of a ceramic-based interference microwave absorbing composite prepared by a high-temperature foaming method

Experimental and numerical research on high‐temperature thermal insulation performance of lightweight porous ceramic/nanomaterial composite structure

Low temperature fired CaF<sub>2</sub>-based microwave dielectric ceramics with enhanced microwave properties

Preparation of high–strength closed–pore foamed ceramics from desalted sea sand at temperatures below 1000 °C

Fe-doped SiC/SiO2 Composites with Ordered Inter-Filled Structure for Effective High-Temperature Microwave Attenuation

Hollow-grained “Voronoi foam” ceramics with high strength and thermal superinsulation up to 1400 °C

Fabrication and properties of Si2N2O ceramics for microwave sintering furnace

Polymer-Derived Lightweight SiBCN Ceramic Nanofibers with High Microwave Absorption Performance

Low‐Temperature Sintering and Microwave Dielectric Properties of Ba5Nb4O15–BaWO4 Composite Ceramics for LTCC Applications

Principles, Design, Structure and Properties of Ceramics for Microwave Absorption or Transmission at High-Temperatures