Abstract:The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb 3 Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb 3 Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb 3 Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb 3 Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid—Nb 3 Sn, NbTi—common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

Design of a New Duplex Magnet for 80 T at WHMFC

Magnet circuit design and optimization of giant magnetostrictive transducer

Design Optimization and Performance Investigation of Linear Doubly Salient Slot Permanent Magnet Machines

Design and Performance of the First Dual-Coil Magnet at the Wuhan National High Magnetic Field Center

Design and Test of a 90-T Nondestructive Magnet at the Wuhan National High Magnetic Field Center

Concept Design of 100 T Pulsed Magnet at the Wuhan National High Magnetic Field Center

The Magnet Design for the HLS Storage Ring Upgrade Project

The Conceptual Optimal Design of a 300MJ High Temperature Superconducting Magnet

The Design and Winding Method of A Conduction-Cooled 1.5 T Bi-2223 High Temperature Superconducting Magnet

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

The Optimal Design Of A 300mj Superconducting Magnet Using Hts Tapes

20 T Dipole Magnet Based on Hybrid HTS/LTS Cos-Theta Coils with Stress Management

Design of A Permanent Quadrupole Magnet with Adjustable Magnetic Field Gradient

The Optimal Design of a 300~MJ Superconducting Magnet Using HTS Tapes

Progress in the Construction of a 20 T REBCO Insert Coil for High-Field All-Superconducting Magnets

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

Development of Superconducting Model Dipole Magnets Beyond 12 T with a Combined Common-Coil Configuration

Design and Preliminary Tests of a 20-T REBCO Insert Coil for a 35-T All Superconducting Magnet

Conceptual Mechanical Structure Analysis of A 16 T Canted Cosine Theta (CCT) Magnet

Design of a 20 T Class REBCO Insert in a 15 T Low Temperature Superconducting Magnet

Structural Design of DC Magnet for Super-X Test Facility