Abstract:Structural evolution and mechanical performances of rapidly solidified Ni95Ge5 and Ni33Ge67 alloys were investigated under two conditions involving drop-tube containerless processing and copper-mold injection casting. As the cooling rate increased, the coarse dendritic structure of the primary (Ni) phase for Ni95Ge5 alloy changed to equiaxed grains structure, and the microstructure of Ni33Ge67 alloy showed a transition from coarse (NiGe + Ge) eutectic to refined structure plus some primary Ge phase. Containerless processing can produce finer microstructures than those of injection casting owing to higher cooling rate. Nanoindentation measurements indicated that both alloys showed a remarkable enhancement of Vickers hardness along with the microstructural evolution, and the hardening mechanism for a single-phase alloy was found to be grain-boundary strengthening, while that of the eutectic alloy was attributed to the multiphase coordinated strengthening. The strain hardening exponents of Ni95Ge5 and Ni33Ge67 alloys were calculated as 0.28 and 0.77, respectively. The special morphology evolution and lower strain hardening exponent of Ni95Ge5 alloy remarkably improved the hardening ability. Its hardness increased up to 56.6% that was much higher than the eutectic alloy. Moreover, these alloys displayed different relations between hardness and strength. The average ratio of hardness to strength for Ni95Ge5 alloy was 2.75, while that for Ni33Ge67 alloy was 9.09. Both the experimental evidence and theoretical analysis revealed that obvious enhancements of hardness and strength were achieved using a high cooling rate; thus, the drop-tube processed alloy particles showed better mechanical properties than those of the as-cast alloys owing to their higher cooling rates. It is obvious that rapid solidification conditions can improve the mechanical properties of both the alloys to various degrees.

Dependence of Microhardness on Solidification Processing Parameters and Dendritic Spacing in Directionally Solidified Sn–Ni Peritectic Alloys

Characterization of Microstructural Length Scales in Directionally Solidified Sn-36%Ni Peritectic Alloy

Dependency of Microhardness on Solidification Processing Parameters and Microstructure Characteristics in the Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Primary Dendrite Distribution in Directionally Solidified Sn–36 At.% Ni Peritectic Alloy

Microstructural Length Scales in Directionally Solidified Sn-40 At.%mn Peritectic Alloy Containing Intermetallic Compounds

Effect of Growth Rate on Microstructure Parameters and Microhardness in Directionally Solidified Ti–49Al Alloy

Research on Lamellar Structure and Microhardness in Directionally Solidified Ternary Sn–40.5Pb–2.6Sb Eutectic Alloy

Research on Lamellar Structure and Micro-Hardness of Directionally Solidified Sn-58bi Eutectic Alloy

Primary Dendrite Arm Spacing During Unidirectional Solidification of Pb–Bi Peritectic Alloys

Dependency of Microstructure Parameters and Microhardness on the Temperature Gradient for Directionally Solidified Ti–49Al Alloy

Solute Redistribution and Micromechanical Properties of Rapidly Solidified Multicomponent Ni-based Alloys

Rapid dendritic solidification and structure hardening mechanism of substantially undercooled quaternary nickel alloys

Microstructure and Microhardness of Directionally Solidified NiAl–W Eutectic Alloy

Dendrite Coarsening in Directionally Solidified Sn–36 At.%ni Peritectic Alloy in the Presence of the Migration of Secondary Dendrite Arms

Dendritic Morphology Evolution and Microhardness Enhancement of Rapidly Solidified Ni-based Superalloys

Influence of Directional Solidification Variables on Primary Dendrite Arm Spacing of Ni-based Superalloy DZ125

Microstructural Evolution and Mechanical Properties of Rapidly Solidified Ni-Ge Alloys

Primary Dendrite Growth of Ni3Sn Intermetallic Compound During Rapid Solidification of Undercooled Ni-Sn-Ge Alloy

Effect of Peritectic Reaction on Dendrite Coarsening in Directionally Solidified Sn–36 At.%ni Alloy

Response of primary dendrite distribution to deceleration growth conditions in a SnNi peritectic alloy

Influence of Growth Rate on Microstructural Length Scales in Directionally Solidified NiAl-Mo Hypo-Eutectic Alloy