Abstract:In this study, combustion synthesis involving mechanical milling and subsequent sintering process was utilised to fabricate Cu/AlxCuy/Al2O3 in-situ composite through the aluminothermic reduction of CuO powders. First, CuO and Al powders were mixed, and ball milled for 30–150 min to facilitate self-propagating high-temperature synthesis (SHS). Then, mechanically activated Al-CuO powders were mixed with elemental Cu powders and experienced subsequent cold compaction and sintering processes. The reactions during synthesis were studied utilising differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Densification and hardness of green and sintered bodies were also obtained. The results indicated that despite the negative free energy of the aluminothermic reaction, an initial activation energy supply is required, and mixed Al-CuO powders did not show significant progress in the combustion synthesis method. The aluminothermic reaction became probable whenever the activation energy was entirely provided by high-energy ball milling or by the sintering of ball-milled Al-CuO mixed powders. DTA results showed that the aluminothermic reaction temperature of Al-CuO decreased with milling times, whereas after 150 min of ball milling, the reaction was completed. XRD patterns revealed that the formation of Al2Cu and Al2O3 reinforcing phases resulted from CuO reduction with Al. Al4Cu9, Cu solid solution, and Al oxide phases were observed in sintered samples. The relative density of the samples was reduced compared to the green compacted parts due to the nature of the Cu-Al alloy and the occurrence of the swelling phenomenon. The hardness results indicated that in-situ formation of reinforcing phases in samples that experienced thermally assisted thermite reaction yielded superior hardness.

STUDY ON THE THERMODYNAMICS OF CuO／Al IN SITU Al2O3 REINFORCED Al MATRIX COMPOSITES

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Study of Hot-press Sintering Process of Nanometer Cu-Al_2O_3 Composite

Nanostructured Composite Obtained by Mechanically Driven Reduction Reaction of Cuo and Al Powder Mixture

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Influence of adding Cu element on properties of Al/Al2O3 composite materials

In situ Al2O3 particle-reinforced Al and Cu matrix composites synthesized by displacement reactions

Mechanical Activation-Assisted Solid-State Aluminothermic Reduction of CuO Powders for In-Situ Copper Matrix Composite Fabrication

Probing on Mutual Interaction Mechanisms of the Ingredients of Al/CuO/PVDF Nanocomposites

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Effect of Sintering Temperature on Al<sub>2</sub>O<sub>3</sub>/TiAl Composite from Ti-Al-TiO<sub>2</sub>-Eu<sub>2</sub>O<sub>3</sub> System

Effect of Sintering Temperature on Al2O3/TiAl Composite from Ti-Al-TiO2-Eu2O3 System

CARBOTHERMIC REDUCTION SYNTHESIS AND REACTION DYNAMICS OF ALUMINUM OXYCARBIDE

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Design of a Thermally Stable Heat-Resistant (Al2O3+Al3Ti)/Al Composite with Excellent High-Temperature Mechanical Properties: Multimechanism Synergistic Strengthening Strategy

Study on Thermal Chemical Reaction of Al/MnO2 Thermite

Research on reaction characteristics and mechanisms of Al-ZnO system powder

Theoretical and experimental study of precipitation and coarsening kinetics of θ′ phase in Al–Cu alloy