Fundamental Modes of Slab Lasers

Xuequan Lu,Shaomin Wang

1988-01-01

Chinese Journal of Lasers

Abstract:Based on the viewpoint that slab lasers have intrinsic quasi-phase-conjugation properties and a new matrix with the optical beam passing through an inclined interface, we show that the fundamental modes of slab lasers have different beam spot size and beam divergence.

What problem does this paper attempt to address?

THE MODES AND PROPERTIES OF THE SLAB LASERS

Xuequan Lu,Shaomin Wang

1988-01-01

Abstract:The zig-zag slab geometry of solid state lasers, which is knows as an excellent method greatly to reduce the problem of thermally induced optical distortions in the pumped laser medium (1,2,3,4,5)
Wavelength-scale Deformed Microdisk Lasers

Q. H. Song,Li Ge,J. Wiersig,J. -B. Shim,J. Unterhinninghofen,A. Eberspaecher,W. Fang,G. S. Solomon,Hui Cao

DOI: https://doi.org/10.1103/physreva.84.063843

2011-01-01

Abstract:We investigate lasing and output directionality of limacon-shaped microdisk lasers of dimensions comparable to the emission wavelength. The far-field patterns are shown to differ between lasing modes, unlike in large cavities where lasing modes exhibit universal emission directionality determined by chaotic ray dynamics. Unidirectional emission is obtained for certain modes in the wavelength-scale cavities. It results from weak coupling of nearly isotropic high-quality resonances to anisotropic low-quality resonances, combined with chiral symmetry breaking of clockwise and counterclockwise propagating waves. The latter is described by an extended ray dynamics which includes the Goos-Hanchen shift and the Fresnel filtering. Mode hybridization and wave effects in open cavities make it possible to control the output properties of individual lasing modes in wavelength-scale lasers.
Phase-dependent laser equations

L.A. Lugiato,Kaige Wang,Yinguan Sun

DOI: https://doi.org/10.1016/0030-4018(94)90414-6

IF: 2.4

1994-01-01

Optics Communications

Abstract:A simple cubic laser model is formulated which describes the interaction of three cavity modes in such a way that the phases of the mode amplitudes play a key role in determining the behavior of the system. It is shown is that this set of equations applies in the case of a cylindrically symmetrical laser operating with the three modes of a frequency-degenerate family. Calculated are, in complete analytical form, all the stationary solutions and their bifurcations in the space of the control parameters.
Exploring the Origin of Lissajous Geometric Modes from the Ray Tracing Model

Xin-Liang Zheng,Yu-Han Fang,Wei-Che Chung,Cheng-Li Hsieh,Yung-Fu Chen

DOI: https://doi.org/10.3390/photonics11050456

IF: 2.536

2024-05-14

Photonics

Abstract:In this paper, we use the geometric optics and discuss the path of laser beam in a simple laser (concave-plano) cavity with the birefringence crystal. In specific lengths of the laser cavity, we can observe various types of Lissajous-like structural laser modes that can be simulated using our ray tracing model. At the end of this paper, we provide an adjusted ABCD matrix. With the adjusted ABCD matrix and iterative calculation, we can obtain the 3D trajectories which are similar to the experimental results. These structural laser modes can be realized by a Nd:YVO4 solid-state laser with off-axis pumping. From the comparison between the experimental data and the numerical data, we clarify the relationship between the 3D Lissajous-like structural laser modes and ray trajectory in the laser cavity.

optics
Robust Slab-Coupled Buried-Rib Semiconductor Laser with High Fibre Coupling Efficiency

G Ru,X Yu,J Cai,J Yan,FS Choa

DOI: https://doi.org/10.1049/el:20047171

2004-01-01

Electronics Letters

Abstract:A robust, single transverse mode slab-coupled buried-rib waveguide laser by combining the concept of slab-coupled waveguide and the technique of diluted waveguide is demonstrated. The large mode size and near-circular mode profile result in high fibre coupling efficiency and improved alignment tolerance.
Index-Tunable Structured-Light Beams from a Laser with an Intracavity Astigmatic Mode Converter

Jing Pan,Yijie Shen,Zhensong Wan,Xing Fu,Hengkang Zhang,Qiang Liu

DOI: https://doi.org/10.1103/physrevapplied.14.044048

IF: 4.6

2020-10-26

Physical Review Applied

Abstract:Structured-light lasers are highly topical due to not only their ability to tailor customized distribution of intensity, phase, orbital angular momentum (OAM), and other optical properties, but also the compact and simple at-the-source generation scheme. Here we propose a form of structured-light laser, intracavity mode convertor laser, with the ability to generate two-dimensional (2D) tunable high-order Hermite-Gaussian (HG) modes with a large indice range (up to 15). The mode convertor constituted by two cylindrical lenses is always used for external OAM conversion, but here we show that it can be inserted into a laser cavity as an intracavity element for symmetry-breaking control, which we also demonstrate with a complete matrix optics theory. The generated 2D HG modes can also be converted into Laguerre-Gaussian (LG) vortex beams with both tunable OAM and radial momentum. Moreover, we also show the ability to directly generate vortex beam from our laser cavity. Our approach meets the urgent necessity for a practical laser device for more versatile light, providing more alternative parametric space for structure control and fostering extended applications.

physics, applied
A New Beam Co2-Laser

S Wang,X Lu

IF: 3.1

1995-01-01

Optik

Abstract:We report that the multi-mode oscillation can be restrained to produce new beam output if a lambda/2 phase plate is put inside CO2 laser cavity.
The laser mode split by rotating an intracavity, tilt cut crystal quartz plate around its surface normal

Shulian Zhang,Wenkai He

DOI: https://doi.org/10.1016/0030-4018(93)90142-R

IF: 2.4

1993-01-01

Optics Communications

Abstract:The mode split is studied by rotating an intracavity crystal quartz plate around its normal line by 360°. There is an angle between each two of the surface normal, crystalline axis and laser beam. The frequency split can exceed one or a few longitudinal mode spacing. The larger the angle between the laser beam and normal line, the larger the slope of the curve of split versus rotating angle. The mode split in the range from 0° to + 180° is symmetric with respect to that in the range from 0° to − 180°. Also the shrinkage phenomenon that the mode split decreases with the rotating angle increasing over some angle range, is observed.
Development of Resonator Analysis Applied in Hybrid Slab Laser with Consideration of Optical Gain and Thermal Lens Effect.

Xingkun Ma,Lei Huang,Mali Gong,Qiang Liu,Haitao Zhang,Ping Yan

DOI: https://doi.org/10.1364/ao.52.004858

IF: 1.9

2013-01-01

Applied Optics

Abstract:By introducing the rate equations and light intensity propagating equations into the fast Fourier transform-based calculation, the optical gain served as the connection between the light field and light intensity, its influence over mode pattern was studied. Thermal lens effect was also investigated by means of finite element analysis. The analysis was applied to a slab laser with a hybrid cavity. A similar experimental study was also carried out in the laboratory. TEM(00) mode with sidelobes along the unstable direction was observed both in the calculation and experiment. As predicted in the analysis, the homogeneity of the pump light improved the beam quality. Numerical and experimental results of pump threshold and slope efficiency were also presented.
Analysis of Leaky Modes of Photonic Crystal Slabs with Deeply Patterned Lattice

Hao Zhang,Heyuan Zhu,Liejia Qian,Dianyuan Fan

DOI: https://doi.org/10.1088/1464-4258/8/5/019

2006-01-01

Journal of Optics A Pure and Applied Optics

Abstract:We demonstrate that leaky modes can be observed in asymmetrical photonic crystal slabs on low-index and high-index substrates. The reflective spectra are studied using the scattering-matrix method, and bands of the leaky modes are obtained via the surface-coupling technique. Caused by the lack of the vertical translational symmetry, the transverse electric (TE)-polarized incidence is reflected into light containing a transverse magnetic (TM) component when the incident plane does not possess mirror symmetry, although the conversion efficiency is weak. This phenomenon, i.e. polarization conversion, is studied in detail.
The Research on Improving the Characteristics of Laser Output with Diffractive Optical Elements

XH Lu,KK Huang

DOI: https://doi.org/10.7498/aps.50.1409

IF: 0.906

2001-01-01

Acta Physica Sinica

Abstract:The matrix eigenvalues method is used to analyze the laser cavity in which the traditional spherical mirror is replaced by the phase type diffraction optical elements. The authors analyze, the characteristics of the modes under the conditions of different Frenesl number. The results show that this laser cavity can enhance the discrimination between spatial modes effectively and can be used to design the output laser beam.
Spectral singularities and threshold gain of a slab laser under illumination of a focused Gaussian beam

DOI: https://doi.org/10.1007/s12648-022-02536-4

2022-11-28

Indian Journal of Physics

Abstract:Spectral singularities of an infinite planar slab containing homogeneous optically active material at the focal plane of a thin lens are investigated. The field distribution of the beam behind the lens is Gaussian that we approximate by a plane wave concentrated near the optical axis at the focal plane of the lens, such that its phase and amplitude are distance-dependent. The consequences of this configuration are explored by determining the threshold gain of the active medium and tuning the resonance frequencies related to spectral singularities. We find that the spectral singularities and the threshold gain, besides that, vary with distance from the center of the Gaussian beam; also they change with the relative aperture of the focusing lens. Numerical studies show that for the central rays of the beam compared to the side rays, the resonances related to the spectral singularities occur at lower wavelengths (higher frequencies) with the highest threshold gain. Also, for the ray at a fixed distance from the center of the beam, increasing the relative aperture of the illuminating system leads to the same results. Numerical results confirm the theoretical findings.

physics, multidisciplinary
Analysis of the pump-beam path in a corner-pumped slab laser

Chen Li,Qiang Liu,Mali Gong,Gang Chen,Ping Yan

DOI: https://doi.org/10.1070/QE2007v037n06ABEH013425

2007-01-01

Quantum Electronics

Abstract:The propagation of the pump radiation in active slab elements is considered. Conditions of the total internal reflection of the pump radiation are obtained, and Eire used to construct a series of graphical illustrations of reflection characteristics of different active elements.
Transverse Mode Switchable Fiber Laser with a Multimodal Interference-Based Beam Shaper

Wentan Fang,Xiaohui Ma,Yong Zhou,Wei Zhang,Xiaolin Chen,Song Huang,Meisong Liao,Yasutake Ohishiand,Weiqing Gao

DOI: https://doi.org/10.1364/ol.478033

2022-01-01

Abstract:We propose a Yb-doped fiber laser with an all-fiber beam shaper based on a single-mode-graded-index multimode-few-mode fiber (SMF-GIMF-FMF) structure. The excitation coefficients of the mode can be adjusted continuously by changing the GIMF length. Numerical simulations are performed to investigate the beam shaping dynamics in the fiber structure. Through adding the simple device geometry in the laser cavity, the switchable output between the fundamental transverse (LP01) mode and the second-order transverse (LP11) mode can be achieved. Cylindrical vector beams with high mode purity are also shown by removing the degeneracy of the LP11 mode.
Multiaxial Super-Geometric Mode Laser.

Jing Pan,Zhaoyang Wang,Ziyu Zhan,Xing Fu,Yijie Shen,Qiang Liu

DOI: https://doi.org/10.1364/ol.485163

2023-01-01

Abstract:Structured light was usually studied by two-dimensional (2D) transverse eigenmodes. Recently, the three-dimensional (3D) geometric modes as coherent superposed states of eigenmodes opened new topological indices to shape light, that optical vortices can be coupled on multiaxial geometric rays, but only limited to azimuthal vortex charge. Here, we propose a new structured light family, multiaxial super-geometric modes, enabling full radial and azimuthal indices coupled to multiaxial rays, and they can be directly generated from a laser cavity. Exploiting combined intra- and extra-cavity astigmatic mode conversions, we experimentally verify the versatile tunability of complex orbital angular momentum and SU(2) geometry beyond the limit of prior multiaxial geometric modes, opening new dimensions to revolutionize applications such as optical trapping, manufacturing, and communications.
Transverse mode changing and frequency splitting of cat-eye cavity laser

Zhaohui Hu,Shulian Zhang,Huibo Jia

DOI: https://doi.org/10.3788/AOS20082801.0123

2008-01-01

Abstract:The former laser systems are complex to realize multiple transverse modes. Only the fundamental mode and low-order modes can be generated, and the high-order modes are hard to be generated. Furthermore, the changing process of one frequency restraining another in mode competition is hard to be observed. A novel synthetical demonstration system of laser principle is presented based on a cat-eye cavity laser and the frequency splitting technology. In the system, a cat-eye retroreflector is treated as the cavity mirror of a He-Ne laser. More than ten typical transverse modes including fundamental mode, low-order modes, and high-order modes can be generated by adjusting the distance between two lenses in the retroreflector. In addition, more experiments of fundamental laser characteristics, such as longitudinal mode, laser polarization, and lasing bandwidth, are also carried out. In the condition of fundamental transverse mode, with a quartz crystal plate put in the cavity, laser frequency splitting and frequency difference adjusting can be achieved. Based on it, the dynamic process of mode competition can be observed.
Distributed-Side-Pumped Slab Lasers: Theoretical Design and Modeling

Xing Fu,Qiang Liu,Mali Gong

DOI: https://doi.org/10.1109/jqe.2010.2091258

IF: 2.5

2011-01-01

IEEE Journal of Quantum Electronics

Abstract:We present a novel pump scheme for slab lasers as distributed-side-pumping. This allows large absorption length, large pump area, and relatively uniform pump profile. We optimize the parameters of slab and pumping system, and carry out numerical calculation of thermal effects in the composite slab and homogeneous slab. Design of 1-kW distributed-side-pumped slab oscillator is described as well.
Properties of the Finite Airy Beam Propagating in the Misaligned Slab System with a Rectangular Aperture

Long Jin,Qiang Zhang,Zhiqiang Yang

DOI: https://doi.org/10.1016/j.rinp.2018.11.022

IF: 4.565

2018-01-01

Results in Physics

Abstract:In this letter, we deduce the approximate analytical formula for the finite Airy beam propagating in the misaligned slab system with a rectangular aperture by using the generalized Huygens-Fresnel integral equation, the light transfer matrix and expanding the hard-edged rectangular function into a finite sum of complex Gaussian function. The particular cases of this beam propagating in the apertured aligned slab system, unapertured misaligned slab system and unapertured aligned one are further illustrated through numerical examples as well. The effects of aperture size and misaligned factors on beam evolution in these slab structures are developed, which can provide a fast and effective method for investigating other kinds of pseudo non-diffracting laser beams through the rectangularly apertured misaligned slab system because most of the optical devices are slightly misaligned more or less in the practical application.
Analysis and Modeling of a Thermal Focal Length in a Corner-Pumped Composite Slab Laser

Q. H. Li,H. Liu,S. Gao,D. M. Christopher,M. L. Gong

DOI: https://doi.org/10.1088/1054-660x/23/1/015804

IF: 1.2

2012-01-01

Laser Physics

Abstract:A simulation method was developed to calculate the thermal focal length for corner-pumped composite slab lasers. Traditional methods assume a uniform heat distribution or an exponential decay heat distribution to simplify the calculation, but the results do not agree well with experimental data for the thermal focal length, which affects the laser resonator design. In the current model, the heat distribution is obtained from the ray trace software Tracepro, which can accurately calculate the pump light absorption distribution in the gain medium. The simulation results with this method have a relative error of 4% compared to experimental results, which is much better than traditional methods with relative errors of 14% for corner-pumped composite slab lasers and demonstrates the effectiveness of this method for the development of new lasers.
Three-Dimensional Coupled-Wave Theory Analysis of A Centered-Rectangular Lattice Photonic Crystal Laser with A Transverse-Electric-Like Mode

Chao Peng,Yong Liang,Kyosuke Sakai,Seita Iwahashi,Susumu Noda

DOI: https://doi.org/10.1103/physrevb.86.035108

IF: 3.7

2012-01-01

Physical Review B

Abstract:A general coupled-wave theory analysis is presented for centered-rectangular lattice photonic crystal (PC) lasers with transverse-electric-like polarization. This analysis affords a realistic approach to the treatment of the full three-dimensional structure of the laser devices by incorporating surface emission and high-order coupling effects. Band structures and radiation constants of band-edge modes are calculated and discussed for different lattice angles, and their accuracies are verified via experiments and numerical simulations. Thus, the proposed analysis facilitates comprehensive understanding of the physics of PC surface-emitting lasers (PC-SELs), and it reveals extra degrees of structural flexibility for developing novel PC-SEL devices.

Fundamental Modes of Slab Lasers

THE MODES AND PROPERTIES OF THE SLAB LASERS

Wavelength-scale Deformed Microdisk Lasers

Phase-dependent laser equations

Exploring the Origin of Lissajous Geometric Modes from the Ray Tracing Model

Robust Slab-Coupled Buried-Rib Semiconductor Laser with High Fibre Coupling Efficiency

Index-Tunable Structured-Light Beams from a Laser with an Intracavity Astigmatic Mode Converter

A New Beam Co2-Laser

The laser mode split by rotating an intracavity, tilt cut crystal quartz plate around its surface normal

Development of Resonator Analysis Applied in Hybrid Slab Laser with Consideration of Optical Gain and Thermal Lens Effect.

Analysis of Leaky Modes of Photonic Crystal Slabs with Deeply Patterned Lattice

The Research on Improving the Characteristics of Laser Output with Diffractive Optical Elements

Spectral singularities and threshold gain of a slab laser under illumination of a focused Gaussian beam

Analysis of the pump-beam path in a corner-pumped slab laser

Transverse Mode Switchable Fiber Laser with a Multimodal Interference-Based Beam Shaper

Multiaxial Super-Geometric Mode Laser.

Transverse mode changing and frequency splitting of cat-eye cavity laser

Distributed-Side-Pumped Slab Lasers: Theoretical Design and Modeling

Properties of the Finite Airy Beam Propagating in the Misaligned Slab System with a Rectangular Aperture

Analysis and Modeling of a Thermal Focal Length in a Corner-Pumped Composite Slab Laser

Three-Dimensional Coupled-Wave Theory Analysis of A Centered-Rectangular Lattice Photonic Crystal Laser with A Transverse-Electric-Like Mode