Abstract:Methodologies of API 579 have been widely accepted as the de-facto standard guideline for fitness for service assessment on crack-like flaws in pressure equipment. For different purposes and needs, the evaluation is divided into three levels, from critical length estimation in level 1, use of the failure analysis diagram (FAD) in level 2, to performing finite element stress analysis in level 3, that is from simplified to accurate. It is generally considered safe as long as the crack is smaller than the critical crack, but not all of them are actually the case. Therefore, it is very important to study the physical meaning behind the critical crack and understand the conservativeness of it.In this study, numerous examples of critical cracks determined according to API 579 Level 1 were put into Level 2 analysis for comparison. Each case is mapped onto the FAD of level 2 analysis to see its position and distance from the borderline between safe and danger zones. A huge amount of examples covering the majority of possible scenarios, including the geometry, thickness, inner diameter, pressure and half-length of the flaw, depth of the crack, crack tip and crack bottom, as a whole, there are 960 cases to be analyzed.Results show that cracks on the circumferential direction of the cylindrical and spherical vessels are distributed tightly in a small area far from the borderline on the FAD diagram. In these cases, the vessel is actually not as dangerous as the critical crack implies, since most of the points lie quite far from the danger zone. As for the longitudinal cracks of a cylindrical vessel, the results are scattered around, and three data points are located outside the allowable zone. The peculiar results are partly due to a discrepancy of interpolating procedure as the influence coefficient is being computed. Through this study, it is also found that the cumbersome process of estimating the critical crack length can be greatly simplified for longitudinal cracks in a cylindrical vessel.

Study on Failure Assessment Curves for Safe End of Nuclear Pressure Vessels

Effects of Initial Crack Location on Failure Assessment Curves in Dissimilar Metal Weld Joints in Nuclear Power Plants

FAD Method for Explosion Containment Vessels Based on API 579 - 1/ASME FFS - 1

Effect of Dissimilar Metal Weld Overlay between Pipe-nozzle of Nuclear Pressure Vessel and Safe End on Failure Assessment Curves

Evaluation of Fatigue Crack Growth Curves in Existing Codes and A Proposed Modification Based on Experimental Data of Cr-Ni-Mo-V Steel Welded Joints

A Modified Time-Dependent Failure Assessment Diagram for Cracks in Mismatched Welds at High Temperatures

Research On Safety Assessment Method For Pressure Pipe With Incomplete Welding Defects Under Complicated Loadings

Investigation of the Quality Category Approach for BS7910-based Rapid Fatigue Assessment of Welded Structures Containing Cracks

Applicability investigation on failure assessment diagram of ASME code section XI - Appendix H for ferritic nuclear piping

Determination of the critical length of the crack-like flaws and its effect on safety

Experimental study on fatigue crack growth behavior and fracture toughness of SA508-III steel for nuclear reactor pressure vessel

FAD of Different Welded Structures for Joining Safe End to Pipe-Nozzle of Nuclear Pressure Vessel

Defect Assessment for Pressure Vessels Considering Crack Growth and Strain Hardening

Constraint characterization and fracture initiation analysis for semi-elliptical surface cracks in reactor pressure vessel

Comparison of Specification Method and Analysis Method for Fracture Prevention Analysis of Reactor Vessel

Data-driven probabilistic failure assessment curve based on similitude principle

Ductile and Brittle Failure Assessment of Containment Vessels Subjected to Internal Blast Loading

Failure Mechanisms and Fatigue Strength Reduction Factor of a Cr-Ni-Mo-V Steel Welded Joint Up to Ultra-Long Life Regime

Numerical Investigation of Ductile Crack Growth Behavior in a Dissimilar Metal Welded Joint

Assessing Toughness Levels for Nuclear Containment Vessels Steel to Determine the Need for Postweld Heat Treatment Based on the Master Curve Method

Investigation on Fatigue Behaviour of Load-Carrying Fillet Welded Joints Based on Mix-Mode Crack Propagation Analysis