Abstract:The Cu-Cr-Zr copper alloy is known for its outstanding electrical conductivity and fatigue strength. However, the corrosion behaviour of the copper alloy should also be taken into account when adopting it in industrial applications, especially in the marine environments. This research aims to fabricate Cu alloy coupons using the Laser Powder Bed Fusion (LPBF) technique and subsequently test their corrosive performance in simulated seawater. This research confirms that the Cu5Zr precipitate formation during the LPBF process and the Cu2O passive layer formation were the main reason for the enhanced corrosive behavior of the LPBFed copper alloy. The OM (Optical Microscope), FESEM (Field Emission Scanning Electron Microscope) images supported in evaluating melt pool formations and irregularities, and also confirmed the polycrystalline structure. The diffraction pattern from the TEM (Transmission Electron Microscope) analysis confirmed the formation of Cu5Zr precipitate and grain size distribution, while their orientations were obtained from the EBSD (Electron Based Scattered Diffraction) EBSD analysis. Micro hardness was executed on the scanning and building directions, and it was found that the building direction possessed higher hardness of 54 HV0.3 which was 5% higher than in the scanning direction. This significant fluctuation in the hardness value is due to the closely packed equiaxed and columnar grains along the outer and inner regions of the melt pools. Potentio-dynamic polarization (PD) and electrochemical impedance spectroscopy (EIS) tests were performed on the printed copper alloy parts for various immersion periods of 0, 9, 18 and 38 hours. Further, the XRD (X-ray Diffraction) analysis was performed on the corroded surface and it confirmed the Cu2O passive layer and the occurrence of Cu5Zr precipitate. The occurrence of Cu5Zr precipitates and Cu2O passive layer formation helped attain the maximum polarization resistance of 2033.8 ohm and minimum current density of 5.928x10-6 A/cm2 with minimum surface roughness of 3.447μm.

A STUDY OF HOT CORROSION BEHMIOR OF Cu IN MOLTEN (Li,k)_2co_3

A study of hot corrosion behavior of Cu in molten (Li,K)2CO3

Electrochemical Impedance Spectra for the Corrosion of Porous Cu-35mass%Ni-(5,10)mass%Cr Alloys in Molten (0.62li,0.38k)2co3 at 650 °C in Air

Corrosion Electrochemical Kinetic Study of Copper in Acidic Solution Using Scanning Electrochemical Microscopy

Corrosion Behaviour of Copper under Chloride-Containing Thin Electrolyte Layer

Electrochemical impedance spectroscopy during corrosion process of 8090 Al-Li alloy in EXCO solution

Effect of Alloying Mg on Corrosion Resistance of Cu at High Temperature

Corrosion Mechanism of Mechanically Alloyed Mg50ni50 and Mg45cu5ni50 Alloys

Corrosion Behavior of Two Heat Treatment Al-Zn-Mg-Cu Alloys in Different Intergranular Corrosion Solution

Investigation on the electrochemical evolution of the Cu-sn-Pb ternary alloy covered with CuCl in a simulated atmospheric environment

A Study about the Different Corrosion Behavior Between Cu/Mo Bilayer and Mo/Cu/Mo Three-layer Metal Electrode

Study on the Initial Atmospheric Corrosion Behavior of Copper in Chloride-Containing Environments

Corrosion behavior and electrochemical properties of carbon steel, commercial pure titanium, copper and copper–aluminum–nickel alloy in 3.5% sodium chloride containing sulfide ions

Effect of Li on Safety of Cu Components for East

CORROSION BEHAVIOR OF HOT WORK STEEL CONTAININGHIGH Co IN LIQUID MAGNESIUM ALLOY AZ91D

Effects of Ti and Cu Addition on Inclusion Modification and Corrosion Behavior in Simulated Coarse-Grained Heat-Affected Zone of Low-Alloy Steels

Consequence of coherent Cu 5 Zr precipitates and Cu 2 O passive layer formation on the corrosive behaviour of additively processed Cu-Cr-Zr alloy in simulated seawater

Electrochemical study on the hot corrosion behavior of Ni16Cr13Co4Mo alloy in molten NaCl-KCl and NaCl-KCl-Na2SO4

Electrochemical Impedance Spectroscopy Analysis on Aluminum Alloys in EXCO Solution

Insight to corrosion mechanism of 90/10 copper-nickel alloys under different sea depths

Interaction between PCB-Cu corrosion and electrochemical migration under the Coupling of electric field and thin liquid film