Research and Development on Intelligent UPS

Xiuyu He

2002-01-01

Abstract:The paper reviews the development history of UPS at first.Then the functions of the new generation intelligent UPS are described in detail.The implementation methods of software and hardware for intelligent UPS are introduced by two practical examples.Finally,the development trends of UPS in the future are prospected.

What problem does this paper attempt to address?

High-reliability long-backup-time super UPS with multiple energy sources

Haijin Li,Wenping Zhang,Dehong Xu

DOI: https://doi.org/10.1109/ECCE.2013.6647365

2013-01-01

Abstract:The power rating of Uninterrupted Power Supply (UPS) has been increasing continuously. In the near future it will increase to MW and dozens of MW. Reliability and environmental friendliness are critical issues for this application. Aiming at the requirements of ultra-high power UPS, this paper proposes a concept of Super UPS using multiple energy sources (Grid, Gas Turbine (GT), Fuel Cell (FC), Li-ion Battery (LB) and Photovoltaic (PV)) to boost the reliability of system and improve environmental friendliness. Firstly, four typical structures for Super UPS are analyzed and the best choice of structure for ultra-high power high reliability application is given. Then, operation modes of proposed structure for Super UPS are introduced. Finally, results of reliability computation verified that the reliability of Super UPS is much higher than traditional UPS.
General on UPS Control Technology

李锡红,吴建德,何湘宁

DOI: https://doi.org/10.3969/j.issn.1009-3664.2003.01.006

2003-01-01

Abstract:With the development of computer and network communication technology, it has been the important path to improve UPS availability through its manageability and serviceability, which mainly be embodied by its enriched software and hardware functions. The paper brings the concept of smart UPS and introduces the existing UPS control technology. It makes a conclusion on a high intelligent control model and estimates the development of the future UPS control technology.
A Dual-Energy-Source Uninterruptible Power Supply (UPS)

Hao Wang,Dehong Xu,Binci Xu,Haijin Li,Ye Zhu

DOI: https://doi.org/10.23919/ipec.2018.8507541

2018-01-01

Abstract:In this paper, a dual-energy-source uninterruptible power supply system (DES UPS) is investigated. There are two energy sources with independent infrastructures in the system, grid and natural gas pipeline. It boosts the reliability of traditional UPS. Grid is the primary energy source, while natural gas generator (NG-Gen) acts as the secondary energy source for long-time backup. Firstly, reliability and source cost of the system are evaluated. Then, cold-start characteristic of NG-Gen is analyzed and the seamless transfer strategy of DES UPS is proposed based on the cold-start characteristic of NG-Gen. It achieves the uninterruptible load power supply when system operation mode changes at the grid fault. Then the control diagram is designed accordingly and state of the system during working mode transfer is analyzed. Finally, the concept and control strategy of DES UPS are verified in a 10kW prototype.
Generic Derivation of Optimal Architecture for A Resilient Microgrid with Graph Theory

Na Chen,Hao Wang,Haijin Li,Dehong Xu

DOI: https://doi.org/10.1109/pedg.2019.8807521

2019-01-01

Abstract:A resilient microgrid for high-surety power, known as Super Uninterruptable Power Supply (Super UPS), is an evolution of traditional UPS. It consists of multiple sources and multiple energy storage components. Besides high efficiency and low cost, reliable power conversion architecture is required. In this paper, a systemic and machine-based way to derive the optimal power conversion topology for the high-surety power supply with multiple sources and energy storage components is investigated. First is the generation of power supply architectures. The architectures are generated and the reasonable ones are selected based on their connectivity. Second part is the evaluation algorithm including cost evaluation, efficiency evaluation and availability evaluation of a given architecture. After evaluating tens of thousands of topologies of architectures, the optimal architectures can be selected. Finally, taking a real Super UPS as example, the proposed method is applied to find the optimal architectures.
Next-Generation Multi-Functional Modular Intelligent UPS System for Smart Grid

Biao Zhao,Qiang Song,Wenhua Liu,Yi Xiao

DOI: https://doi.org/10.1109/tie.2012.2205356

IF: 7.7

2012-01-01

IEEE Transactions on Industrial Electronics

Abstract:This paper analyzed the development trend of uninterruptible power supply (UPS) and presented a multi-functional modular intelligent UPS system for smart grid, which is composed of four identical H-bridge converters. It not only can realize all the basic functions of the traditional UPS system, but also can realize the cyclic use of the electrical power between the power grid and storage battery. Moreover, due to the modular construction, it can easily change into various power converters for other applications. The topology configuration and operating principle of the proposed UPS system are analyzed, and a distributed control management strategy and a distributed logic control algorithm are proposed. At last, experimental results verify the validity and effectiveness of the proposed system and its control strategy. The exploration of this study could provide some valuable references for the design of next-generation electrical equipment in smart grid.
Research on UPS Based on DSP Dual-loop Control

Hao Ma

2006-01-01

Abstract:A 5 kVA on-line digital controlled UPS based on DSP is presented. To improve the steady state operation and dynamic response, a dual-loop control strategy which incorporates the inductor current and the instantaneous output voltage has been used. The system based on Infineon XC164CM DSP that controls the inverter and the system logic operation is introduced. The power part of the UPS consists of Infineon F4-100R06KL4 IGBT module. The experimental result is given and has proved the design is correct.
Design Of Hybrid Ac-Dc-Ac Topology For Uninterruptible Power Supply

Dezhi Dong,Linglin Chen,Haijin Li,Min Chen,Dehong Xu

DOI: https://doi.org/10.1109/ifeec.2015.7361614

2015-01-01

Abstract:A hybrid AC-DC-AC topology for Uninterruptible Power Supply (UPS) is investigated, which is composed of a two level three-phase four-wire rectifier and a three level T-type inverter. It has distinct advantages for the applications of on line UPS. The grid side power quality can be easily satisfied with the front-end two level three-phase rectifier. Since output voltage's THD is challenge to UPS with sever nonlinear load, the T-type inverter is used to enhance the load power quality with higher conversion efficiency. The rectifier is transformed into step-up converter for the battery during the grid faults. The efficiency optimization of the proposed UPS with the hybrid AC-DC-AC topology is studied. The control strategies for the UPS are investigated. At last, the UPS prototype with 200kVA is designed and tested to validate the performance of the proposed UPS.
Design of a Two-stage Charger for Batteries in UPS

QI Feng,XU Fei,TANG Jian-qing,MA Hao

DOI: https://doi.org/10.3969/j.issn.1000-100x.2007.08.020

IF: 5.967

2007-01-01

IEEE Transactions on Power Electronics

Abstract:A two-stage charger design for 5kVA UPS controlled by XC164 is presented.This charger adopts a combi-nation of Boost and bi-transistor forward and can be applied in a wide range of input voltage and output voltage.It has the advantages of isolation between input and output and good expansion for output power.The experimental results demon-strate that it can satisfy the demand of UPS charger.
The Influence and Design Consideration of Ups Output Virtual Resistance on Parallel-Connected Ups System

Wei Yu,Dehong Xu,Kuian Ma

DOI: https://doi.org/10.1109/apec.2009.4802914

2009-01-01

Abstract:The important characteristics of parallel-connected uninterruptible power supply (UPS) systems are excellent power-sharing quality and stability. In this paper we use the output active and reactive power to adjust the output voltage amplitude and phase to achieve the load sharing. Because of the difference of output filter inductor's resistance and distance of connection wire of each machine in the paralleled UPS system, the equivalent output impedance of each UPS inverter is different. These output impedance difference can cause circulation current and decrease the load-sharing quality. In order to solve this problem, virtual resistance is introduced to each inverter. In this paper the influence of the virtual resistance on paralleled UPS system and how to choose the virtual resistance is analyzed. Experimental studies using DSP controlled parallel-connected three-phase four-wire UPS system are presented to show the effectiveness of the proposed design.
New Development of Three Phase Uninterrupted Power Supply

WANG Lin-bing,HE Xiang-ning

2005-01-01

Abstract:A review of three phase uninterrupted power supply (UPS) systems in terms of each circuit model, the whole system circuit topology, popular control method is described, and the problem of design and application is presentsed. Finally, the new research hot spot and a brief outline of advancement to be made in the future is concluded.
Design of Li-ion Battery Power Conversion System Applied in Super UPS

Jianan ZHOU,Min CHEN,Haijin LI,Ping LIN,Changsheng HU,Dehong XU

DOI: https://doi.org/10.13234/j.issn.2095-2805.2015.3.21

2015-01-01

Abstract:To further increase the reliability, safety of the power supply, concept of the super UPS occurs. Super UPS is composed of multiple sources such as Grid, Gas turbine, Li-ion battery and renewable energy. The Li-ion battery power conversion system need to support the DC bus quickly when emergency happens and cooperated with other two module to stabilize the load supply. In this paper, the demand of the Li-ion battery module is analyzed. Then in order to get a high charging and discharging accuracy, sampling error is analyzed the design of the Li-ion power conversion system is proposed based on the character test of the battery. Finally, the effectiveness of the proposed method is verified in the 10 k W prototype.
Solid State DC Circuit Breaker for Super Uninterruptible Power Supply

Haijin Li,Jianan Zhou,Zhaoyu Liu,Dehong Xu

DOI: https://doi.org/10.1109/PEAC.2014.7038038

2014-01-01

Abstract:In this paper, demand for Solid State DC Circuit Breaker for Super Uninterruptible Power Supply (UPS) is analyzed firstly. Design of the Solid State DC Circuit Breaker is investigated. Then the optimized structure with RCD+MOV is designed to reduce the voltage stress of the power device. Furthermore, the detection of short-circuit current is provided. Finally, a prototype is built to verify the design.
Neural-network-controlled single-phase UPS inverters with improved transient response and adaptability to various loads

xiao sun,dehong xu,f h f leung,yousheng wang,yimshu lee

DOI: https://doi.org/10.1109/PEDS.1999.792820

1999-01-01

Abstract:This paper proposes a neural-network control scheme for the inverters of uninterruptible power supplies (UPS) to improve their transient response and adaptability to various loads. Two simulation models are built to obtain example patterns for training the neural network. One is a multiple-feedback-loop controller for linear loads, and the other is an idealized load-current-feedback controller specially designed for nonlinear loads. The latter controller has a built-in reference load model, and the load current is forced to track this reference. Example patterns under various loading conditions are used in the off-line training of a selected neural network which is made as simple as possible to reduce the calculation time. When the training is completed, the neural network is used to control the UPS inverter on-line. The development of example patterns and training of the neural network are done using MATLAB and SIMULINK, and the verification of results is done using PSpice. It is found that the proposed neural-network-controlled inverter can provide good sinusoidal output voltage with low total harmonic distortion (THD) under various loading conditions, and good transient responses when the load changes
Topology of Super Uninterruptible Power Supply with Multiple Energy Sources

Keyan Shi,Haijin Li,Changsheng Hu,Dehong Xu

DOI: https://doi.org/10.1109/icpe.2015.7168013

2015-01-01

Abstract:The dramatic loss caused by the power blackout in some industrial applications proposes the requirement for an extremely high reliability uninterruptible power supply (UPS). This paper introduces the concept of super uninterruptible power supply (Super UPS). Multiple energy sources are used to obtain a high reliability, long backup time, high surety UPS system. Classifications for energy sources, power conversion stage and power distribution bus line are established to simplify the power conversion architectures. A generic method to classify the architectures for multiple energy source system is presented. Then a system reliability evaluation method based on different architectures is used to analyze the characteristics of different types of topology. Redundant power conversion stage design to enhance the system reliability is discussed. Finally, a high reliability super UPS architecture is proposed.
Unified Control Scheme Design For Both The Pwm Rectifier And The Inverter In The Uninterruptible Power Supply (Ups) System

Keyan Shi,Xiaojun Wang,Dezhi Dong,Changsheng Hu,Dehong Xu

DOI: https://doi.org/10.1109/IFEEC.2017.7992260

2017-01-01

Abstract:This paper first discusses control loop characteristics for the PWM rectifier and the inverter used in an on-line UPS system. Then a unified control scheme for both the PWM rectifier and the inverter in the UPS system is investigated using single phase control in ABC frame. Based on the unified control scheme, a generic control kernel is defined. This generic control kernel is used to realize the main performance of the UPS system, such as dynamic response, low THD and synchronism. Then the generic control kernel can be further applied to both the PWM rectifier and inverter by selecting different inputs. The unified control scheme not only significantly simplifies the UPS control software development, but also improves its maintenance. Finally, this unified control scheme is verified on a 50kVA UPS system.
Multi-Functional Bidirectional AC/DC T-type 3-Level Converter for Super UPS

Ye Zhu,Binci Xu,LingLin Chen,Dezhi Dong,Ping Lin,Dehong Xu

DOI: https://doi.org/10.1109/peac.2014.7037887

2014-01-01

Abstract:Multi-Functional Bidirectional AC/DC T-type 3-Level Converter for Super UPS is investigated in this paper. The AC/DC converter is used as the interfaced between DC Bus and Energy Source or Load. According to the components (grid, gas turbines, AC loads) connected in AC side, The AC/DC converter operates at AC voltage source mode, Power source mode or DC voltage source mode. A control scheme for the Multi-Functional Bidirectional AC/DC converter is studied. Finally the design of the AC/DC converter is verified by experiment on a 100kW AC/DC converter prototype.
A Novel Accurate Active and Reactive Power Calculation Method for Paralleled UPS System

Wei Yu,Dehong Xu,Kuian Ma

DOI: https://doi.org/10.1109/apec.2009.4802827

2009-01-01

Abstract:Among the paralleled UPS control strategies, output droop method and average power control method need to calculate UPS output active and reactive powers accurately for control of the phase (frequency) and amplitude of output voltage. In light or no load conditions, active circulation currents may cause high DC voltages which will damage the machine. This paper suggests using the UPS output filter inductor current instead of the output current when calculating the UPS output active and reactive powers. For improving accuracy of the power calculation, the sampling delay of the inductor current needs to be adjusted. Two digital controlled three-phase four-wire 30 KVA paralleled UPS systems are implemented for experimental verification of the theory analysis. The experimental results show that better current-sharing performance is achieved.
A novel dynamic control strategy on resisting impulsive load for uninterruptible power supply system

Guofeng He,Dehong Xu,Wei Yu,Min Chen

DOI: https://doi.org/10.1109/APEC.2013.6520490

2013-01-01

Abstract:Uninterruptible Power Supply (UPS) is widely used in industry and electronics field in order to improve power quality. However, the distortion and interruption of output voltage will occur when UPS is applied to instantaneous impulsive load. This paper proposes a novel dynamic control strategy to resist impulsive load. When the impulsive load is imposed on UPS instantaneously, the impulsive current can be quickly sensed by the digital controller and the supplying power for the load is switched from inverter to bypass immediately. Therefore, the output voltage of UPS can be maintained uninterruptible. The proposed control strategy is verified by a 30 KVA UPS prototype.
Novel Grid-connected UPS System with the Electricity Feedback Function and Its Distributed Logic Control Strategy

赵彪,于庆广,王立雯,肖宜

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2011.31.001

2011-01-01

Abstract:With the proposal of the construction of smart grid,the single electricity consuming equipment can no longer satisfy the need of the development of smart grid.＂Green＂,energy saving and grid-connected electrical equipment become the main development trend.The paper proposed a novel grid-connected uninterruptible power supply（UPS） system with the electricity feedback function and its circuit topology.The system can be split into four single-phase bridge converters,which,in turn,are grouped to formed pulse width modulation（PWM） rectifier and feeder module,isolated bidirectional DC-DC module and inverter module,so the system becomes a four-quadrant operation power supply device.On this basis,the operation modes of system were designed,and the control system was split into seven modular sub-controllers.With their combinational logic,the control strategy of each module were implemented,so the control targets of steady state and transient state in different modes were achieved.At last,simulation and experimental results verified the validity and effectiveness of the proposed circuit topology and control strategy.
Review on the Technology of on Board DC/DC Conversion for EV Application

li wei,shuai liu,di fu zhan,xu ping cai,zhi dong li,yun xiong,huai sheng ni

DOI: https://doi.org/10.4028/www.scientific.net/AMM.321-324.347

2013-01-01

Applied Mechanics and Materials

Abstract:The paper gives a systemic classification to the common electric vehicle (EV). The technology of low power converter using as auxiliary power supply and high power converter using for traction system has been deeply discussed from the view of topology, control strategy and devices. Finally, the development tendency of on board DC conversion technology is prospected.

Research and Development on Intelligent UPS

High-reliability long-backup-time super UPS with multiple energy sources

General on UPS Control Technology

A Dual-Energy-Source Uninterruptible Power Supply (UPS)

Generic Derivation of Optimal Architecture for A Resilient Microgrid with Graph Theory

Next-Generation Multi-Functional Modular Intelligent UPS System for Smart Grid

Research on UPS Based on DSP Dual-loop Control

Design Of Hybrid Ac-Dc-Ac Topology For Uninterruptible Power Supply

Design of a Two-stage Charger for Batteries in UPS

The Influence and Design Consideration of Ups Output Virtual Resistance on Parallel-Connected Ups System

New Development of Three Phase Uninterrupted Power Supply

Design of Li-ion Battery Power Conversion System Applied in Super UPS

Solid State DC Circuit Breaker for Super Uninterruptible Power Supply

Neural-network-controlled single-phase UPS inverters with improved transient response and adaptability to various loads

Topology of Super Uninterruptible Power Supply with Multiple Energy Sources

Unified Control Scheme Design For Both The Pwm Rectifier And The Inverter In The Uninterruptible Power Supply (Ups) System

Multi-Functional Bidirectional AC/DC T-type 3-Level Converter for Super UPS

A Novel Accurate Active and Reactive Power Calculation Method for Paralleled UPS System

A novel dynamic control strategy on resisting impulsive load for uninterruptible power supply system

Novel Grid-connected UPS System with the Electricity Feedback Function and Its Distributed Logic Control Strategy

Review on the Technology of on Board DC/DC Conversion for EV Application